Gardol GHH-E20Li Manual De Instrucciones página 27

5.8 Adjusting the additional handle
(Fig. 17-18)
(a) Setting the tilt of the additional handle
Open (a) the lock (F). Set the desired tilt of the
additional handle (9). Close (b) the lock (F).
b) Shifting the additional handle
Open (a) the lock (H) and slide the additional
handle (9) into the required position. Close (b) the
lock (H).
5.9 Using the shoulder strap
Warning! Always use the shoulder strap when
working with the equipment. Switch off the equip-
ment before you take off the shoulder strap (risk
of injury).
1. Hook the carabiner (Fig. 4/Item A) into the
strap holder.
2. Slip the shoulder strap (Fig. 19/Item 8) over
your shoulder.
3. Adjust the length of the shoulder strap so that
the strap attachment is at waist level (Fig. 19).
4. The shoulder strap is equipped with a buckle.
Press the hooks together (Fig. 20) if you need
to put down the equipment quickly.
5. To change the strap position on the equip-
ment, press together the two metal loops (Fig.
4/Item L / M) and adjust the strap attachment
on the tube.
5.10. Adjusting the angle of the handle
(Fig. 21)
Press the two safety lock-off s (5) and adjust the
angle of the handle (2) to any of 4 latching posi-
tions.
5.11. Adjusting the angle of the motor
housing (Fig. 22)
Press the two safety lock-off s (14) and adjust the
angle of the motor housing (13a) to any of 7 lat-
ching positions.
5.12 Adjusting the telescopic tube (Fig. 23)
1. Undo the telescopic tube lock nuts (10 + 12)
by turning them counter-clockwise.
2. Pull out the telescopic tubes (11 + 13) to suit
the required working height.
3. Secure the telescopic tube lock nuts (10 +
12) by them turning clockwise.
5.13 Fitting the battery (Fig. 24 – 25)
Press the side pushlock button (T) of the battery
pack as shown in Fig. 24 and push the battery
pack into the mount provided. When the battery
Anl_GHH_E_20_Li_SPK7.indb 27 Anl_GHH_E_20_Li_SPK7.indb 27
GB
pack is positioned as in Fig. 25, make sure that
the pushlock button latches in place! To remove
the battery pack, proceed in reverse order.
5.14 Charging the battery (Fig. 26)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button (T).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(21) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (1) into the battery
charger (21).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless equipment
drops. Never fully discharge the battery pack. This
will cause it to develop a defect.
6. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from one loca-
tion to another.
Caution! Always use the shoulder strap when
working with the equipment. Always switch off the
equipment before you take off the shoulder strap.
Otherwise there is a risk of injury.
Put on the shoulder strap as described above, fi t
the required mounting kit and adjust the equip-
ment to suit your needs.
- 27 -
12.05.15 15:58 12.05.15 15:58