Operation - OWT Industries Clean GC141333 Serie Manual Del Operador

WARNING:
Do not allow familiarity with the product to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to heed this warning could
result in serious injury.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
 Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
 Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
 Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills, play-
ground equipment, etc.
*Always test in an inconspicuous area first.
USING THE DETERGENT INjECTOR
See Figures 10 - 11.
The G-Clean detergent injector allows you to use G-Clean
detergent while using your pressure washer for high and low
pressure cleaning.
NOTE: Use only G-Clean detergent in the injector. Any other
solutions may damage the injector and/or your pressure
washer pump.
 Disconnect pressure washer from power supply.
 Place pressure washer upright on a flat surface.
 Unscrew the cap from the end of the clear tube on the
injector. Remove G-Clean detergent pouch from plastic

OPERATION

bag and place into the tube, then replace the cap and
tighten securely.
NOTE: Make sure the cap is securely tightened. Allowing
air into the injector during use may cause damage to your
pressure washer pump.
 In cold weather when water temperature is below 50ºF,
cut the pouch open and put the detergent directly into
the injector.
 Use the dial on the G-Clean Detergent Injector to choose
water or G-Clean detergent as desired.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figure 12.
NOTICE:
Do not run the pressure washer pump without water sup-
ply connected and turned on, as this may damage the
high pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
 Connect the garden hose.
 Turn the garden hose on then squeeze the trigger to
relieve air pressure. Once a steady stream of water ap-
pears, release the trigger.
 After ensuring the On/Off knob is in the OFF ( O ) position,
connect the pressure washer to the power supply.
 Press the reset button on the pressure washer's plug to
make sure the unit is ready for operation.
 Turn the knob to ON ( I ) to start the motor.
 To stop the motor, release the trigger and turn the knob to OFF
( O ).
NOTE: The pressure washer may be on and the sytem
may have pressure even when the pump and/or motor
cannot be heard running. Always use caution around the
pressure washer.
USING THE SPRAY WAND TRIGGER
See Figure 13.
For greater control and safety, keep both hands on the
trigger handle at all times.
 Pull back and hold the trigger to operate the pressure
washer.
 Release the trigger to stop the flow of water through the
nozzle.
To engage the lock-out:
 Push up on the lock out until it clicks into the slot.
To disengage the lock-out:
 Push the lock out down and into its original position.
Page 11 — English