Remoset Function; Identification Number - JTS CS-W4C/5 Manual De Instrucciones

4.5.4.2 Deleting a user-defined group
1) Call up the following menu via the menu item
2.User Group
1.Edit
2.Clear Group
3.Return
2) Turn the knob PUSH / CONTROL to select the
second menu item
press the knob
Group: U1
Rotary to select
Push "Enter" to clear
Push "Exit" to return
3) Turn the knob to select the group to be de-
leted and then press the knob The following
confirmation prompt appears:
Group "Ux" will be
cleared, Continues?
YES NO
4) To cancel the process, press the button EXIT
To delete the group, press the knob
5) To delete further groups, repeat steps 3 and 4;
to exit all menus, press the button EXIT three
times

4.5.5 REMOSET function

Transferring settings to the transmitters
The settings of the transmission frequencies (or
groups or channels) made on the receiver and
other settings can be most conveniently trans-
ferred to the corresponding transmitter by a
press on a button The settings transferred to the
transmitter depend on the configuration of the
REMOSET function in the menu (chapter 4 6 3)
Always make sure that
1 no menu is called up on the receiver or on
the transmitter
2 the transmitter is switched on and close to
the receiver (REMOSET transfer range: ap-
prox 10 m)
3 the REMOSET function is not locked or disa-
bled on the transmitter
4 the transmitter and the corresponding receiver
section are set to the same identification num-
ber
5 the batteries of the transmitter are not dis-
charged
of the highest menu level:
Fig. 23
and then
Clear Group
Fig. 24
Fig. 25

4.5.5.1 Identification number

Each pair of transmitter / receiver must have a dif-
ferent identification number (ID no ); this is the
only way to make sure that each transmitter is
supplied with the settings intended The receiver
sections 1– 4 are preset to the identification num-
bers 1– 4 Resetting will also reset the receiver
sections to these numbers When further receivers
CS-W4C are used, they must be assigned dif-
ferent identification numbers (e g the second
receiver must be assigned the numbers 5 – 8):
1) Keep the button SETUP pressed to call up
the menu Turn the knob PUSH /CONTROL
to select the receiver section to be changed
(CH 1– 4) Press the knob and then select item
5.Remoset ID
chapter 4 3 )
Remoset ID
1
2) Turn the knob PUSH /CONTROL to set the
identification number
3) Press the button SETUP to save the setting
4) Press the button EXIT to go to the highest
menu level; then repeat the setting for the
other receiver sections
5) Make sure to set each transmitter to the identi-
fication number of the corresponding receiver
section (chapter 4 8)
4.5.5.2 REMOSET transmission
1 For four transmitters at the same time
Press the button REMOSET (5) During the
REMOSET transmission, the display shows
for the four receiver sections, the
Syncing...
button REMOSET button keeps flashing and the
LED status indicators (24) on the transmitters
CS-W4T light up in blue As soon as the four
corresponding transmitters have been set, the
button REMOSET lights continuously again
If the flashing of the button REMOSET slows
down after approx 80 seconds, automatic set-
ting of at least one transmitter has failed o fewer
than four transmitters are being used To stop
the flashing, press the button EXIT For trouble-
shooting see steps 1– 5 at the beginning of chap-
ter 4 5 5 Check the settings on the correspond-
ing transmitter and correct them, if necessary
Then press the button REMOSET again
in the submenu (fig 7 in
Fig. 26
29