Seconds Until Power Off; Shown On The Display; Setting The Volume; 2 Wireless Microphone Cs-W4T - JTS CS-W4C/5 Manual De Instrucciones

Indication Meaning
Transmission frequency
MHz
(506,000 ... 542,000 MHz)
Status of the batteries of the
transmitter
– when no signal is being received
or when the transmitter is muted
(not possible for CS-W4T), the
message
instead of the battery symbol
– as long as the battery status has
not been transferred yet,
be shown
The output level adjusted by means
of the buttons
,
Mute
Fig. 33 Display information
3) To switch off the receiver, keep the button
pressed for 2 seconds until

shown on the display

5.1.2 Setting the volume

Use the buttons
 
volume of the four microphone channels These
volumes will also be used when the signals are
routed to the output MIXED AF OUTPUT (20)
5.1.3 Key lock
The receiver is provided with a key lock to prevent
inadvertent switch-off or operation: Keep the but-
ton (9) pressed for 1 second until the symbol
appears on the left side of the display To de-
activate the key lock, keep the button pressed for
2 seconds until the symbol

5.2 Wireless microphone CS-W4T

To switch on the wireless microphone CS-W4T,
move the sliding switch (22) on the rear side to
the position ON or LOCK The power LED indica-
tor (24) will light up in green When the switch
is moved to the position LOCK, the display (25)
will briefly show
phone can be used for speaking; however, it is
not possible to change the settings of the micro-
phone When the sliding switch is moved back
to the position ON, the display will briefly show
and will then show the frequency set or
the group / channel
Press the button (29) to speak The LED indi-
cator (26) will light up in red After speaking, press
the button again; the LED indicator will extinguish
will be shown
MUTE
(13) :
 
...
-31 0 dB
Power OFF
(13) to separately adjust the
disappears
In this position, the micro-
Note: Whether the person speaking can be heard via
the receiver when the LED indicator (26) lights up in
red, also depends on the priority settings on the receiver
(chapter 4 7)
To save the batteries, use the switch (22) to switch
off the microphone (position OFF) after usage and
possibly during longer speech pauses

6 Specifications

Carrier frequency range: 506 – 542 MHz
REMOSET frequency:
will
Ambient temperature:
CS-W4C /5
Receiver sections:
Audio outputs
Frequency range:
Output impedance:
is
Separate outputs CH 1– CH 4
Output level:
Connection:
Output Mixed AF Output
Output level:
Connection:
THD:
Dynamic range:
Power supply:
Power consumption:
Dimensions (W × H × D): 485 × 45 × 260 mm,
Weight:
CS-W4T/5
Power supply:
Dimensions of console
housing (W × H × D):
Gooseneck length:
Weight:
2 4 GHz
0 – 40 °C
4
60 – 16 000 Hz
600 Ω
63 mV (Mic), switcha-
ble to 630 mV (Line)
XLR, balanced
sum signal of
CH1– CH4 + LINK IN,
level switchable:
Line or Mic
XLR, balanced and
6 3 mm, unbalanced
< 0 6 %
> 105 dBA
110 – 240 V/ 50 – 60 Hz
20 VA max
1 RS
2 4 kg
2 × 1 5 V
non-rechargeable
battery (AA)
or 2 × rechargeable
NiMH battery
138 × 29 × 116 mm
400 mm
720 g
Subject to technical modification
33