Publicidad
Idiomas disponibles
Idiomas disponibles
English
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified
personnel only.
Owner's Record
The model and lot numbers are located on the bottom of your AC adapter. Record the lot
number in the space provided below. Refer to the model and lot numbers when you call your
Sony dealer regarding this product.
Model No. PEGA-AC510
Lot No.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including any interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual
could void your authority to operate this equipment.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
• CLIÉ and Jog Dial are trademarks of Sony Corporation.
• HotSync is a registered trademark, and the HotSync logo is a trademark of Palm, Inc. or its
subsidiaries.
®
®
• Microsoft
and Windows
are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
• All other trademarks are trademarks of their respective owners.
Before use
The Travel Kit provides for convenient mobility, allowing you to use the CLIÉ handheld
wherever you go. With the Travel Kit, you can:
• Charge the battery with the AC adapter.
Since the supplied AC adapter automatically converts both frequency and voltage, an additional
converter is not needed when charging the battery. (AC 100 to 240 V, 50-60 Hz)
• Synchronize (HotSync
®
) data between the CLIÉ handheld and your computer by
using the USB HotSync cable.
Note
Do not connect the supplied AC adapter to the converter designed for traveling purposes. It may result
in an excessive heat and malfunction.
Charging directly from the power supply
When you connect the supplied AC adapter to the CLIÉ handheld, battery charging
automatically begins. The battery indicator in the Applications Launcher display changes to
.
Connect to the wall
outlet
z
To use the AC adapter when traveling overseas, you may need to purchase the plug
adapter that allows plugging to desired country pin configuration.
To disconnect the AC adapter from your CLIÉ handheld
Connect the AC adapter to
the interface connector
Pinch both sides of the
connector and pull out.
Printed on recycled paper
Connecting the USB HotSync cable
By using the USB HotSync cable, you can synchronize data between the CLIÉ handheld and
your computer.
Connect to the
USB connecter
Note
Make sure the Palm Desktop for Sony software is installed in your computer.
To disconnect the USB HotSync cable from your CLIÉ handheld
Performing local HotSync
1
Click
icon in the task tray at the bottom right corner of the
Microsoft
®
Windows
®
Desktop and make sure that Local is checked
in the shortcut menu.
Tip
If the
icon is not displayed in the task tray, start the HotSync manager by clicking Start -
Program - Sony handheld - HotSync manager.
2
Press the CLIÉ handheld power button.
3
Tap
icon.
4
Rotate the Jog Dial navigator to select HotSync and press the Jog
Dial navigator.
The HotSync dialog box appears on the screen.
5
Make sure Local is selected (not Modem) and tap V to select Direct
Serial.
6
Tap
icon of the CLIÉ handheld.
HotSync starts automatically.
When HotSync is finished, a HotSync completion message is displayed.
Specifications
AC Adapter (PEGA-AC510)
Input
100 - 240 V AC, 50 - 60 Hz, 0.15 A
Output
5.7 V DC, 800 mA
Operating temperature 5˚C to 35˚C (41˚F to 95˚F)
Mass
Approx. 90 g (3.17 oz.)
Cord length
Approx. 1.8 m (70
USB HotSync Cable
Mass
Approx. 30 g (1.06 oz.)
Cord length
Approx. 1 m (39
Supplied accessories
AC adapter (1)
USB Hotsync cable (1)
Operating Instructions (1)
Design and specifications are subject to change without notice.
Notes on use
• Do not place the unit in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Vibrating
– Subject to strong magnetic fields
– Sandy
– Exposed to direct sunlight
• Do not apply mechanical shock or drop the unit.
• Unplug the AC adapter from the AC outlet when not in use for a long time. To disconnect
the power cord, pull it out by the plug. Never pull the cord itself.
• Be sure that nothing metallic comes into contact with the metal parts of this unit. If this
happens, a short circuit may occur and the unit may be damaged.
• Do not operate the unit with a damaged cord or if it has been dropped or damaged.
• Always keep the metal contacts clean.
• Do not disassemble or convert the unit.
• While the unit is in use, it gets warm. This is normal.
• Keep the unit away from TV or AM receivers, as it will disturb reception.
On cleaning
Clean the unit with a soft dry cloth, or a soft cloth lightly moistened with a mild detergent
solution. Do not use any type of solvent, such as alcohol or benzine, which may damage the
finish.
Connect the USB
HotSync cable to the
interface connector
Pinch both sides of the
connector and pull out.
7
/
inches)
8
3
/
inches)
8
Publicidad
