Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
To operate the Electronic Clock/Programmer
1
. ELECTRONIC PROGRAMMER
Preliminary Operations to Perform After Plugging-in the Oven.
After initially plugging-in the unit, and after each interruption in power, the lighted display on the
control panel will respond by flashing «AUTO»
Press the
and
buttons along with the
When the
symbol appears on the display, the oven is ready to be used manually.
Available Functions
— Manual operation
— Timed operation
— Semi-automatic operation (programmed end to the cooking time)
— Automatic operation (programmed beginning and end of cooking time)
Manual Operation (of the oven):
This has already been described in the section of PRELIMINARY OPERATIONS. Just press
the
button to make the corresponding symbol appear in the center and remove the AUTO
indicator.
Using the Electronic Programmer
As described in the PRELIMINARY OPERATIONS section, the electronic programmer allows the
oven to be operated manually or by:
— The timer;
— Programming the end of the cooking time (semi-automatic operation);
— Programming the beginning and end of the cooking time (automatic operation).
Using the Timer
While pressing the
button, use the
maximum). Setting the desired time will light the
either as a manual function or automatic along with another program).
At the end of the set time the programmer sounds an intermittent signal, to cancel the signal
press
. While cooking, to display the time remaining press
Adjusting the Tone of the Timer Signal
Three different tones are available on the acoustic timer signal. To choose the bone desired,
press the — button while the signal is sounding.
or
buttons to set the exact time.
and
buttons to select the desired time (23:59
symbol. (Note: This function can be used
.
7
Semi-Automatic Programming (end of cooking time)
Select oven temperature and cooking function.
To program only the shut-off (and not the turn-on) time of the oven proceed as follows.
Press the
button along with either the
set the display to the desired cooking time. Release the buttons. The display responds by lighting
the
symbol and «AUTO», indicator.
The
symbol on the display means the oven has begun to cook.
At the end of the cooking time, the oven shuts-off automatically, the programmer sounds a tons,
the
symbol vanishes from the display, and the «AUTO» indicator begins to blink.
Remember that when the «AUTO» indicator is blinking, the
turn the oven to manual operation.
To display the cooking time remaining while cooking, press the
button shows the time when cooking will end
Automatic Programming (beginning and end of cooking time)
Select oven temperature and cooking function.
To program not only the oven shut-off time, but also the cooking time (and hence the turn-on
time) the following steps must be performed:
1) Press and hold the
desired cooking time.
Upon releasing the buttons, the display will again show the current time, the «AUTO»
indicator, and the
2) Press and hold the
time cooking is to finish.
When the buttons are released, the display will again show:
— The current time;
— The «AUTO» indicator.
Once the above steps are completed, the oven will automatically turn on and off at the desired
times.
The oven turn-on time will automatically be determined by the oven, based on the cooking times.
When the oven begins operation, the programmer will display with
indicator. When the oven shuts-off, the tone sounds and the
indicator begins to blink.
Remember that when the «AUTO» indicator is blinking, the
the oven to manual operation.
The tone signaling the end of the cooking time can be canceled by pressing the
To display the cooking time remaining while cooking, press the
button shows the time when cooking will end.
Warning: The symbols on the buttons may vary from model to model, but their functions
remain the same.
EN
EN
or
button, and, while holding the buttons,
button and use the
and
buttons to set the display to the
symbol.
button and use the
and
buttons to set the display to the
symbol disappears. The «AUTO»
button must be pressed to return
8
button must be pressed to re-
button. Pressing the
symbol and the «AUTO»
button.
button. Pressing the
Publicidad
Tabla de contenido
