Protective Features - BLACK&DECKER PI500P Manual De Instrucciones

Ocultar thumbs

Contenido

página de 19

/ 19
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

INTRODUCTION

Congratulations on purchasing your new Black & Decker 500 Watt Power Inverter. Read this

Instruction Manual and follow the instructions carefully before using your new inverter.

This power inverter is configured to supply continuous power in the form of two 120 volt AC outlets

and a 5 volt USB charging port to run most household or electronic appliances.

Controls and Functions

100w LED

InDICATor

TrAnSLuCEnT on/oFF BuTTon

AnD PowEr/FAuLT InDICATor

PIVoTInG

ThrEE-PronG

120 VoLT AC

ouTLETS

uSB ChArGInG

PorT

(rED) PoSITIVE

DC PorT (For uSE

CABLE PoST

wITh ThE 12V DC

(unDEr CAP)

VEhICLE ADAPTEr

(rED) PoSITIVE

PoST GrooVE

PI500P_ManualEnFrSP_061213.indd 4-5

500w LED

InDICATor

MounTInG BrACkETS

(ToTAL oF 4, 2 on ThE LEFT,

AnD 2 on ThE rIGhT)

VEnTILATIon

SLoTS

(BLACk) nEGATIVE

hIGh-SPEED

CABLE PoST

CooLInG FAn

(unDEr CAP)

(BLACk) nEGATIVE

PoST GrooVE

12V DC VEhICLE

ADAPTEr PLuG wITh

hAnGInG hook

DC DouBLE-BArrEL

HOW THIS INVERTER WORkS

This inverter is an electronic device that converts low voltage DC (direct current) electricity from a

battery to 120 volts AC (alternating current) household power. It converts power in two stages. The

first stage is a DC-to-DC conversion process that raises the low voltage DC at the inverter input to

145 volts DC. The second stage is a MOSFET bridge stage that converts the high voltage DC into 120

volts, 60 Hz AC.

Power Inverter Output Waveform

The AC output waveform of this inverter is known as a modified sine wave. It is a stepped waveform

that has characteristics similar to the sine wave shape of utility power. This type of waveform

is suitable for most AC loads, including linear and switching power supplies used in electronic

equipment, transformers, and small motors.

CAUTION – Rechargeable Devices

• Certain rechargeable devices are designed to be charged by plugging them directly into an AC

receptacle. These devices may damage the inverter or the charging circuit.

• When using a rechargeable device, monitor its temperature for the initial ten minutes of use to

determine if it produces excessive heat.

• If excessive heat is produced, this indicates the device should not be used with this inverter.

• This problem does not occur with most battery-operated equipment. Most of these devices use a

separate charger or transformer that is plugged into an AC receptacle.

• The inverter is capable of running most chargers and transformers.

CAUTION: incompatible products: Certain products contain power supplies or circuits that are not

compatible with a inverter using a modified sine wave output (such as this inverter) and may be

damaged by using this inverter.

If your product requires pure sine wave AC input power to function properly, the instruction manual

for your product could state this. If in doubt, you should contact your product manufacturer PRIOR

TO USE.

Some products must be powered from a pure sine wave power source, such as standard household

power, or a "pure sine wave" inverter in order to function properly.

Your product could be damaged by this inverter if it contains:

• Microwave ovens;

• Transformerless battery chargers

• Capacitive coupled power supplies

If an incompatible product is used with this inverter:

• The product might not operate at all, with no indication of failure. The product fuse might open as a

result of trying to use it with the inverter.

• The product might exhibit unusual operation (such as, intermittent operation, buzzing, and the like.)

WARNING: If the product does not operate normally, to reduce the risk of injury or property

damage, turn the product off immediately and unplug it from the inverter.