Setup; Ac Power; Ac Plug; Mounting - Chauvet Professional VIP Drive 43 Nova Manual De Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

3. S
ETUP

AC Power

Each VIP Drive 43Nova has an auto-ranging power supply that works with an input voltage range of 100 to
240 VAC, 50/60 Hz. To determine the power requirements for each VIP Drive 43Nova, refer to the label
affixed to the product. You can also refer to the
The listed current rating indicates the maximum current draw during normal operation. For more
information, download Sizing Circuit Breakers from the Chauvet website: www.chauvetprofessional.com.
• Always connect the product to a protected circuit (circuit breaker or fuse). Make
sure the product has an appropriate electrical ground to avoid the risk of
electrocution or fire.
• To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.

AC Plug

The VIP Drive 43Nova comes with a power input cord terminated with a Neutrik® powerCON® connector
on one end and an Edison plug on the other end (U.S. market). If the power input cord that came with your
product has no plug, or if you need the change the plug, use the table below to wire the new plug.
C
ONNECTION
AC Live
AC Neutral
AC Ground

Mounting

The VIP Drive 43Nova fits nicely on a standard 19" rack, or it can be placed on its rubber feet on a flat level
surface.

Signal Connections

The VIP Drive 43Nova uses the NOVA control protocol to send video signal to the connected panels. The
VIP Drive 43Nova has USB and Ethernet ports for interfacing with a computer, HDMI, HD-SDI and DVI
ports for video input, as well as 4 Neutrik® etherCON® out ports, an HDMI out port, and a 5-pin DMX out
port.

Video Source Connection

You can link the VIP Drive 43Nova directly to a video source using a DVI connection, an HDMI connection,
or an HD-SDI connection.

NovaLCTMars Connection

You can link the VIP Drive 43Nova to a computer running the NovaLCTMars software using a USB (type A
or B) connection or an ethernet cable. This will provide control options for the VIP Drive 43Nova through a
computer interface.

DMX Connection

With DMX, you can control the color balance and dimmer levels for all connected panels. You can link the
VIP Drive 43Nova to a DMX controller using a 5-pin DMX connection. If using other DMX-compatible
products with this product, you can control each individually with a single DMX controller. The DMX Values
section provides detailed information regarding the control personalities.
If you are not familiar with or need more information about DMX standards or the
DMX cables needed to link this product to a DMX controller, download the DMX
Primer from the Chauvet website: www.chauvetprofessional.com.

Preview Monitor Connection

You can link the VIP Drive 43Nova to a monitor that will preview the LED output using an HDMI cable
plugged into the PREVIEW HDMI port.

Cascading Connection

You can link multiple VIP Drive 43Nova products together in a cascading connection using the USB type A
and B connections on the rear panel of the product. This will allow all products to be programmed at once.
5
Technical Specifications
W
(U.S.)
IRE
Black
White
Green/Yellow
chart in this manual.
W
(E
)
IRE
UROPE
Brown
Blue
Green/Yellow
VIP Drive 43Nova User Manual Rev. 3
S
ETUP
S
C
CREW
OLOR
Yellow or Brass
Silver
Green

Publicidad

Tabla de contenido
loading

Tabla de contenido