EGO BCA1200 Manual De Usario página 10

2. Rotate the outer flange to align the slot in the inner
EN
flange with the shaft-locking hole in the gear case
(Fig. F).
3. Insert the hex wrench provided into the aligned holes
to act as a stabilizer (Fig. G).
Fig. F & G parts description see below:
F-1 Gear Case
F-2 Aligned Shaft-locking
Holes
4. Position the brush cutter head against a solid surface
for support. With one hand grasping the brush cutter
shaft and use the other hand to grasp the multi-
function wrench provided to loosen the nut in the
direction of the arrow marked on the outer flange and
remove the nut and the outer flange. Save them for
reassembly (Fig. H).
5. Mount the blade onto the motor shaft, ensuring that
the surface of the blade is flush with the surface of
the inner flange bulge. Go on mounting the outer
flange and the nut (Fig. I). Pre-tighten the nut in
COUNTERCLOCKWISE by hand.
Fig. I parts description see below:
I-1 Inner Flange Bulge I-4 Outer Flange
I-2 Motor Shaft
I-3 Nut
6. Rotate the outer flange to align the slot in the inner
flange with the shaft-locking hole in the gear case
and insert the hex wrench provided into the aligned
holes to act as a stabilizer as previous step 2 & 3
shown.
7. Position the brush cutter head against a solid surface
for support. With one hand grasping the blade and
use the other hand to grasp the multi-function
wrench provided to tighten the nut opposite the
direction of the arrow marked on the outer flange
(Fig. J).
Use of Guard Accessory
NOTICE:
When the tool is used as a line trimmer
equipped with a trimmer head, the guard accessory must
be mounted onto the guard (Fig. K).
Secure the guard accessory onto the guard by tightening
the three screws with the hex wrench provided. Failure
to comply could result in an overly long cutting line and
motor overload.
10
BRUSH CUTTER ATTACHMENT — BCA1200
CONNECTING THE BRUSH CUTTER ATTACHMENT TO
THE POWER HEAD
This brush cutter attachment is designed for use with EGO
Power Head PH1400E.
See "INSTALLING AN ATTACHMENT TO THE POWER
HEAD" section in the power head PH1400E operator's
manual.
F-3 Outer Flange
G-1 Stabilizer
OPERATION
to make you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
hearing protection. Failure to do so could result in objects
being thrown into your eyes and other possible serious
injuries.
APPLICATIONS
You may use this product for the purpose listed below:
◾
I-5 Blade
NOTICE:
purpose. Any other use is deemed to be a case of misuse.
USING THE BRUSH CUTTER WITH POWER HEAD
injury when operating this tool. Do not wear loose clothing
or jewelry. Wear eye and ear/hearing protection. Wear
heavy, long pants, boots and gloves. Do not wear short
pants or sandals or go barefoot.
For safe and better operation, put on the shoulder strap
across the shoulder. Adjust the shoulder strap in a
comfortable operating position. Hold the brush cutter
with one hand on the rear handle and the other hand on
the front-assist handle. Keep a firm grip with both hands
while in operation. The brush cutter should be held at
a comfortable position with the rear handle about hip
height. Maintain your grip and balance on both feet.
Position yourself so that you will not be drawn off balance
by the kickback reaction of the cutting blade (Fig. B).
release mechanism in hazardous situation. When
emergency occurs, take it off from your shoulder
immediately, no matter what way the strap is in.
WARNING:
Do not allow familiarity with this product
WARNING:
Always wear eye protection, along with
Cutting malted grass, weeds, wild growth and scrub,
thinning young stands with a maximum stem diameter
of 2cm.
The tool is to be used only for its prescribed
WARNING:
Dress properly to reduce the risk of
WARNING:
The shoulder strap is also a quick