Safety Precautions; Operating The Tool - Powers Fasteners P3500 Manual De Instrucciones

MODEL P3500
.300 HEAD DIAMETER DRIVE PINS WITH 3/4" WASHER
CAT. STD.
NO. SHANK LENGTH BOX
50070 3/4" 100
50080 2-1/2" 100
50082 3" 100
.300 HEAD DIAMETER DRIVE PINS WITH 7/8" WASHER
CAT. STD.
NO. SHANK LENGTH BOX
50090 1" 100
50092 1-1/4" 100
50094 1-1/2" 100
50096 2" 100
50098 2-1/2" 100
50100 3"* 100
.300 HEAD DIAMETER DRIVE PINS WITH 1" WASHER
CAT. STD.
NO. SHANK LENGTH BOX
50108 1-1/4" 100
50110 1-1/2" 100
50112 2" 100
50114 2-1/2" 100
50116 3" 100
.300 HEAD DIAMETER DRIVE PINS WITH 1-7/16" INSULATION WASHER
CAT. STD.
NO. SHANK LENGTH BOX
50122 1-1/2" 100
50126 2-1/2" 50
50132 3" 50
1/4"-20 THREADED STUDS
CAT. THREAD SHANK STD.
NO. LENGTH LENGTH BOX
50320 1/2" 1/2"K 100
50322 3/4" 1/2"K 100
50326 3/4" 3/4" 100
50328 1/2" 1" 100
50330 3/4" 1" 100
50334 1/2" 1-1/4" 100
50336 3/4" 1-1/4" 100
50338 1-1/4" 1-1/4" 100
.300 HEAD DIAMETER PINS WITH CEILING CLIPS
CAT. SHANK STD. STD.
NO. LENGTH BOX CTN.
50363 1" 100 1000
50364 1" 100 1000
50368 1" 100 1000
50370 1-1/4" 100 1000
50374 1-1/4" 100 1000
.300 DIAMETER HEAD DRIVE PINS WITH BX CABLE STRAPS AND CONDUIT CLIPS
CAT. STD.
NO. DESCRIPTIONBOX CTN.
50150 1" 100
50152 1-1/4" 100
50380 1/2" EMT 1-1/4" pin 100
50381 1/2" EMT 1" pin TH 100
50382 1/2" EMT 1" pin 100
50384 3/4" EMT 1-1/4"pin 100
50385 3/4" EMT 1" pin TH 100
50386 3/4" EMT 1" pin 100
50388 1" EMT 1" pin TH 25
.300 HEAD DIAMETER PIN WITH REBAR BASKET CLIP
CAT. STD.
NO. DESCRIPTION BOX
50702 32mm w/ basket clip 100
50704 37mm w/ basket clip 100
50710 47mm w/ basket clip 100
50712 52mm w/ basket clip 100
50716 62mm w/ basket clip 100
50718 72mm w/ basket clip 100
FORMING PIN
CAT. STD.
NO. DESCRIPTION BOX
50790 62mm - 2-1/2" 100
50789 44mm - 1-3/4" 100
P3500
5
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
1000 .300 .143 1.6
1000 .300 .143 2.5
1000 .300 .143 2.8
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
1000 .300 .143 1.9
1000 .300 .143 2.0
1000 .300 .143 2.1
1000 .300 .143 2.4
1000 .300 .143 2.7
1000 .300 .143 3.0
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
1000 .300 .143 2.2
1000 .300 .143 2.3
1000 .300 .143 2.6
1000 .300 .143 2.9
1000 .300 .143 3.2
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
1000 .300 .143 2.1
500 .300 .143 2.7
500 .300 .143 3.0
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
5000 1/4" .143 .8
1000 1/4" .143 1.1
1000 1/4" .143 1.2
1000 1/4" .143 1.2
1000 1/4" .143 1.4
1000 1/4" .143 1.4
1000 1/4" .143 1.5
1000 1/4" .143 1.7
HEAD SHANK WIRE WT./
DIA. DIA. HOLE 100
.300 .143 0.278" 3.4
.300 .143 0.278" 3.5
.300 .143 0.278" 3.0
.300 .143 0.278" 3.7
.300 .143 0.278" 3.2
STD. HEAD SHANK WT./
DIA. DIA. 100
1000 .300 .143 3.5
1000 .300 .143 3.7
1000 .300 .143 3.4
1000 .300 .143 3.3
1000 .300 .143 3.3
1000 .300 .143 3.5
500 .300 .143 3.4
1000 .300 .143 3.3
250 .300 .143 3.2
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
100 8mm .143 4.0
100 8mm .143 4.1
1000 8mm .143 4.3
1000 8mm .143 4.4
1000 8mm .143 4.6
1000 8mm .143 4.8
STD. HEAD SHANK WT./
CTN. DIA. DIA. 100
1000 .205 .143 1.4
1000 .205 .143 1.1
K=Knurled TH=Top Hat
CAT. NO.52000/Deluxe Kit

Safety Precautions

Safety is your primary responsibility when operating any
powder actuated tool. You must read and understand the
contents of this manual. You must be familiar with all functional
and safety requirements of the tool. It is your responsibility to
obtain proper training and a Powers Fasteners operator card prior
to using this tool in compliance with the current American
National Standard A10.3 Safety Requirements for Powder
Actuated Fastening Systems and the Federal Occupational Safety
and Health Administration Standards (OSHA). Existing state or
local regulations should also be followed. When using this tool,
you must have the qualified operators card in your possession.
Revocation of card - Failure to comply with any of the rules and
regulations for safe operation of powder actuated tools shall be
cause for the immediate revocation of your qualified operator card.
The following is a summary of safety precautions to be
followed when operating a Powers Fasteners powder actuated
tool. Failure to follow these safety instructions can result in
serious injury or death to operators or bystanders.
PRIOR TO OPERATING THE TOOL
1. WARNING SIGNS SHOULD ALWAYS BE POSTED
WITHIN THE AREA IN WHICH A POWDER ACTUATED
TOOL IS TO BE USED. THESE SIGNS SHOULD BE AT
LEAST 8" X 10" IN SIZE WITH BOLDFACE TYPE THAT
IS NOT LESS THAN 1" IN HEIGHT. THE SIGN SHOULD
STATE "POWDER ACTUATED TOOL IN USE".
2. Approved safety goggles should always be worn by operator
or bystander, to protect their eyes from flying particles. Hearing
protection should always be worn by the operator and
bystanders when using a powder actuated tool. Other personal
safety protection as required should also be used.
3. Never modify or fabricate parts for use in your Powers tool.
Use only Powers fasteners, loads, and tool parts.
4. Hands or other body parts must never be placed in front of
muzzle/barrel. Accidental discharge can cause piston and/or
fastener to pass through the operator's hand.
5. Never compress the tool against any part of the body.
Serious injury or death may result in the event of an accidental
discharge.
6. Always point tool in a safe direction at all times.
7. Use the tool for its intended purpose only.
PREPARATION FOR LOADING THE TOOL
1. Tools must be checked prior to operating to make sure they
are not fully or partially loaded with a powder load or fastener.
2. To insure safe operation, perform the daily function test
described in this manual. Be sure the tool is not loaded prior to
performing this test.
3. Do not operate this tool unless all its parts are in place and
operating appropriately. Never attempt to use a malfunctioning
tool. Call 1-800-524-3244 for assistance.
4. Never guess about the suitability of a base material. If you
are uncertain about the suitability of a base material, perform a
center punch test.
5. Do not operate the tool until you learn and understand the
color code / numbering system used to identify the power level
of powder loads.

OPERATING THE TOOL

1. Only use fasteners and powder loads designed for this tool
as supplied by Powers Fasteners.
2. Do not use powder actuated tools in a flammable or an
explosive atmosphere.
52001/Blister Pack
®