4-Digit Code Programming; Search Code By Brand Name; Auto-Search Programming - Rotel RR-1090 Manual De Instrucciones

10 RR-1090

4-Digit Code Programming

Find your audio/video component in the code list
and note the 4-digit code(s):
1. Press the MENU button to reach the main menu.
2. Select SETUP from the LCD display menu by
pressing the MENU COMMAND key above the
first letter of the SETUP label.
3. Press one of the DEVICE buttons to select where
you wish to store this component's codes. If you
choose the multipurpose AV1, AV2, or AV3 de-
vice buttons, you will be further prompted to se-
lect the type of component (CD, VCR, etc.)
4. Select ENTER CODE by pressing the MENU
COMMAND key above that label.
5. Input the 4-digit code using the MENU COM-
MAND keys corresponding to the digits in the
LCD display. Upon completion, the successfully
entered code will be confirmed in the display.
6. Once the code has been entered, the menu will
present two options. Press another DEVICE key
to program additional codes. Press the MENU
button to return to the main menu; press the MENU
button a second time to exit the setup mode and
return to normal operation.
Test the code by sending commands to the compo-
nents (i.e. the POWER command). If the code does
not work properly, repeat the procedure using the
next 4-digit code listed for the brand of component.

Search Code by Brand Name

You can also use the following search method to find
and test the code numbers available for your brand
of component.
1. Press the MENU button to reach the main menu.
2. Select SETUP from the LCD display by pressing
the MENU COMMAND key above the first let-
ter of the SETUP label.
3. Press one of the DEVICE buttons to select where
you wish to program this component's codes. If
you choose AV1, AV2, or AV3, you will be fur-
ther prompted to select the type of component
(CD, VCR, AMP, etc.).
4. Select BRAND NAME by pressing the MENU
COMMAND key above that label.
5. Select the first letter of your component's brand-
name. If necessary, press the M4 button for the
next page of letters or the M3 button for the
previous page of letters.
6. Select your component's brand name from the
list appearing in the display (pressing M4 or M3
for additional listings). The prompt "press POWER
key to test" appears in the display
7. Press the POWER button on the right side of the
RR-1090 to test the first available code for your
brand. The 4-digit code being tested is shown
in the display.
If the POWER command turns on or off the
desired component, you have found a code that
may work. You can test additional commands by
pressing MENU COMMAND keys corresponding
to commands for that 4-digit code shown in the dis-
play. If successful, press the DEVICE button to save
the code.
If the POWER command does not work, press
the POWER button to test the next available code
for that brand, with the new 4-digit code being tested
shown in the display. Continue pressing the POWER
button and testing codes until you have found a code
that works, saving it by pressing the DEVICE button.
If none of the available codes for that brand
work, you will be asked to search the entire library
of codes for that kind of component. Select YES to
jump to the search procedure (step 5 in the follow-
ing section). Select NO to return to the main menu

Auto-Search Programming

To search for a code from the full list of available 4-
digit codes for a type of component:
1. Press the MENU button to reach the main menu.
2. Select SETUP from the LCD display menu by
pressing the MENU COMMAND key above the
first letter of the SETUP label.
3. Press one of the DEVICE buttons to select where
you wish to program this component's codes. If
you choose AV1, AV2, or AV3, you will be fur-
ther prompted to select the type of component
(CD, VCR, AMP, etc.).