Tabla de contenido
Publicidad
Check Spray Gun and Spray Tip Extension
Examinehoseconnectionto spraygun and makesure it is
secure.Testtrigger by pressingit and makingsure it springs
back into placewhenyou releaseit. Do not depress red button
and test trigger. You should not be able to presstrigger. Replace
spray gun immediatelyif it fails anyof thesetests.
Spray Tip Maintenance
A pulsing sensation felt while squeezing the spray gun trigger
may be caused by excessive pump pressure. The principal
cause of excessive pump pressure is a spray tip clogged or
restricted with foreign materials, such as dirt, etc. To correct
the problem, immediately clean the spray tip following these
instructions:
1.
Shut off engine and turn off water supply.
2.
ALWAYSpoint spray gun in a safe direction, press red
button and and squeezespray gun trigger to release
retained high water pressure.
_i, WARNING The high pressure stream of water that
this equipment produces can cut through skin
and its underlying tissues, leading to serious
injury and possible amputation.
Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause
injury.
* Keephigh pressure hoseconnected to pumpand spraygun
whilesystemis pressurized.
* ALWAYSpointspraygun in safedirection,pressred button
andsqueeze sprayguntriggerto release highpressure, e very
time you stop engine.
3.
Remove spray tip from end of spray tip extension.
4.
Use a small paper clip to free any foreign material
clogging or restricting spray tip (A).
5.
Remove spray tip extension from spray gun.
6.
Using a garden hose, remove additionaldebris by back
flushing water through spray tip extension. Backflush
between 30 to 60 seconds.
7.
Reinstall spray tip into spray tip extension.
8.
Reconnect spray tip extension to spray gun.
9.
Make sure garden hose is connected to water inlet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
10. Start engine following instructions How to Start Your
Pressure Washer.
11. Test pressure washer by operating with each quick
connect spray tip.
O-Bino Maintenance
Purchasean O-Ring RepairKit, item 7175116, at your local
Searsor by calling 1-888-4-1VlY-NOME ( 469-4663) or online at
www.sears.com, it is not includedwith the pressurewasher.
This kit includes replacement o -rings and a water inlet filter.
Referto the instruction sheetprovidedin the kit to serviceyour
unit's o-rings.
_i, WARNING The high pressure stream of water that
this equipment produces can cut through skin
and its underlying tissues, leading to serious
injury and possible amputation.
* NEVER repairleakingconnections with sealant o f any kind.
Replace o-ring or seal.
ENGINE MAINTENANCE
_i, WARNING
Unintentional sparking can result in fire or
_
electric shock.
WHENADJUSTINGOR MAKING REPAIRSTO YOUR PRESSURE
WASHER
* Disconnect the spark plug wire from the spark plug and place
the wire where it cannot contact spark plug.
WHENTESTINGFOR ENGINESPARK
* Useapproved spark plug tester.
. DO NOT check for spark with spark plug removed.
Oil
8il Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service SF, SG,
SH, SJ or higher. DO NOT use special additives.
Outdoor temperatures determine the proper oil viscosity for
the engine. Use the chart to select the best viscosity for the
outdoor temperature range expected.
oF
104___
506886
_o__
32 .o
14
-4
-22
°C
\
40
;_30
°_20
10
_m
m
0
--_C
°
-20
-30
* Below40°F(4°C)the useof SAE30 will result in hardstarting.
** Above80°F(27°C)the useof 10W30maycauseincreased oil
consumption. C heckoil levelmorefrequently.
O
OTICE Synthetic oil meeting ILSAC GF-2, API
certification mark and API service symbol with
"SJ/CF ENERGY CONSERVING"or higher, is an
acceptable oil at all temperatures. Use of synthetic oil
does not alter required oil change intervals.
16
Publicidad
Tabla de contenido
