Fitting The Ceramic Logs; Fitting The Optional Pebbles Set - Thermocet TRIMLINE Serie Instrucciones De Instalación

4. PLACEMENT OF THE CERAMIC LOG AND OPTIONAL PEBBLE SET
Before placing the optional Wall or Slats set
(I2L / I2ELL) the premix brackets underneath the
image 8)
Method:
* Remove the deco plate and double burner out of the burning chamber.
* Unscrew both premix brackets from the burner.
* Place the premix brackets for G20 with the holes Ø 5 mm
* Place the premix brackets for G20//20-25 with the holes Ø 7 mm
* The burner pressure and the injector need not be changed.
* Loosen the screws holding the bottom and top glass holders (2).
* Place the suction cup(s) in the middle of the glass-panel and remove the panel by GENTLY
moving this first upwards and then the lower edge of the glass-panel very carefully and slowly
pulling toward you. Then place in a safe place where the window can not be broken or damaged.
If the removed glass panel is damaged (scratched and / or damaged edges) then no longer use the
glass panel and contact your dealer.
* Place the Black glass set very carefully to avoid breakage or damage.
* Follow the instructions strictly as illustrated.
* Replace the decorative plate.
Note: when installing the log and Pebble set and the various glowing materials and accessories, the fol-
lowing must be taken into account:
A: No glowing material in or on the pilot burner.
B: Prevent that ceramic material falls on the glass seals. Remove this if necessary. The window can be damaged.
Slot /opening between burner and mesh deco plate must be kept free of glowing material. Too
C:
much placed glowing material can affect the combustion process.
4.1 Fitting the Ceramic log set (see Appendix 7)
* Mix the glowing material (lava granules) and the "fusilli" (spiral-shaped ceramic material)
and spread them evenly over the burner and the burner plate so that they are just covered.
Glowing embers can be placed here and there as decoration.
Make sure the pilot light remains unobstructed.
* Place the ceramic wood blocks in the correct order as shown on Appendix 7.
* Place the logs carefully. Other location can seriously affect the flames or malfunction of the
burn process (sooting)
* Before replacing the windows make sure if there must be a restriction plate to be placed or not.
See chapter 8 "Concentric chimney lay out"
* If there is a restriction required for your situation, remove the baffle plate by unscrewing it
from the front of the plate and move the plate backwards and then out. Now install the restriction
plate with two screws and replace the baffle plate. (Also see Appendix 5, pictures 7).
* Now place the window in reverse order as described at
on Appendix 5.
4.2 Fitting the optional Pebble set. (see appendix 8)
* Scatter vermiculite evenly over the burner tray. Make sure the pilot light remains unobstructed.
* Place a row of medium-sized and large pebbles at the front of the burner plate
* Fill the burner tray with small and medium-sized pebbles from the front to the rear.
Place the pebbles as closely as possible to each other on the burner tray.
* Fill the rear of the burner plate with medium-sized and large pebbles.
* Before replacing the window make sure if there must be a restriction plate to be placed or not.
See chapter 8 "Concentric chimney lay out"
* If there is a restriction required for your situation, remove the baffle plate by unscrewing it
from the front of the plate and move the plate backwards and then out. Now install the restriction
plate with two screws and replace the baffle plate. (Also see Appendix 5, pictures 7).
* Now place the window in reverse order as described at chapter "PLACING THE APPLIANCE" 2.2 and
on Appendix 5.
NOTICE
MAKE SURE THE PILOT LIGHT REMAINS UNOBSTRUCTED FROM ANY MATERIAL!
only for 73H DB (1133)
double burner needs to be changed. (see appendix 5
chapter "PLACING THE APPLIANCE"
when heating on G25 20-25mBar
2.2 and
Page.6