Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
80
KONECT BRUShLeSS wATeRpROOf eSC - INSTRUCTION MANUAL
amp
High power system for RC model can be very dangerous, so we strongly suggest you read this manual carefully. In that
KONECT have no control over the correct use, installation, application, or maintenance of our products, no liability shall be
assumed nor accepted for any damages, losses or costs resulting from the use of the product.
ANY CLAIMS ARISING FROM THE OPERATING, FAILURE OF MALFUNCTIONING ETC. WILL BE DENIED. WE ASSUME NO LIABILITY FOR
PERSONAL INjURY, CONSEqUENTIAL DAMAGES RESULTING FROM OUR PRODUCT OR OUR WORKMANSHIP. AS FAR AS IS LEGALLY
PERMITTED, THE OBLIGATION TO COMPENSATION IS LIMITED TO THE INVOICE AMOUNT OF THE AFFECTED PRODUCT.
wARNINgS
1.
Ensure all wires and connections are well insulated before connecting the ESC to related devices, as short circuit will
damage your ESC.
2.
Ensure all devices are well connected to prevent poor connection that may cause your vehicle to lose control or other
unpredictable issues such as damage to the device.
3.
Read through the manuals of all power devices and chassis and ensure the power configuration is rational before using this unit.
4.
Please use a soldering iron with the power of at least 60W to solder all input/output wires and connectors.
5.
Do not hold the vehicle in the air and rev it up to full throttle, as rubber tires can "expand" to extreme size or even crack to
cause serious injury.
6.
Stop using the ESC when its casing temperature exceeds 90°C/194°F; otherwise your ESC will get destroyed and may also
get your motor damaged. We recommend setting the "ESC Thermal Protection" to 105°C/221°F (this refers to the internal
temperature of the ESC).
7.
We recommend removing the cooling fan from ESC before exposing vehicle to liquids, and fully dry it right after use.
8.
Always disconnect the batteries after use, as the ESC will continue to consume current if it's connected to batteries (even if
the ESC is turned off). Long-time contact will cause batteries to completely discharge and result in damage to batteries or
ESC. This WILL NOT be covered under warranty.
feATUReS
9.
ESC is compatible with both sensorless and sensored brushless motors (only in sensorless mode).
10. Fully waterproof design for all conditions.
11. Super internal switch-mode BEC with switchable voltage of 6V/7.4V and cont./peak current of 3A/6A for usage with high
torque and high voltage servos.
12. Highly reliable electronic switch design prevent mechanical switch failure due to dirt, water, dust and etc.
13. Separate programming port to easily connect the LED program card or the LCD program box to the ESC.
14. Proportional brake with 9 levels of maximum brake force and drag brake force.
15. 5 levels of acceleration/punch from soft to aggressive for different vehicles, tires and tracks.
16. Capacitor Protection: Innovative Capacitor Protection effectively protects capacitors from exploding and causing
irreversible damage to the ESC from overloading.
17. Multiple protections: motor lock-up protection, low-voltage cutoff protection, thermal protection, overload protection,
and fail safe (throttle signal loss protection).
18. Single-button ESC programming and factory reset.
19. Advanced programming via portable LED program card.
SpeCIfICATIONS
Model
Cont. / Burst Current
Suitable Car
Motor Turns
Battery
BEC output
Motor Type
Dimension & weight
BegIN TO USe The New eSC
This is an extremely powerful brushless motor system. For your safety and the safety of those around you, we strongly recommend removing
the pinion be-fore performing calibration and programming functions with this system, and keeping wheels in the air when you turn on the ESC.
1. Connect the ESC, Motor, Receiver, Battery And Servo
The #A, #B, #C wires of the ESC can be connected with the motor wires freely (without any sequence). If the motor runs in the
opposite direction, please swap any two wire connections.
KONECT 80AMP WP "by HOBBYWING"
80A / 520A
1/10th & 1/8th Buggy, Short Course Truck, Truck and Monster Truck
From 3000Kv to 5400Kv : any 3650 to 3660 sensorless brushless motor
6-9 cells NiMH
2-3S Li-Po
6V/7.4V Switchable, Continuous Current of 3A (Switch-mode)
Sensored / Sensorless Brushless Motor (only in sensorless mode)
49 x 39.5 x 34.7mm (W/Fan) / 105g
9
Publicidad
Tabla de contenido
