Unpacking And Inspection - Flotec FPSS1200X Manual Del Usuario

General Information
DESCRIPTION
This Stainless Steel Submersible Utility Pump is designed
to drain flooded basements, pump domestic waste water,
and pump out gratings and drains. Operates manually.
Has a 115V, 60 Hz., single phase, permanent split capaci-
tor motor. Permanently lubricated ball bearings never need
lubrication. Automatic thermal overload protection. Unit is
equipped with a 15' 18/3 grounding-type power cord.
Discharge is 1-1⁄4".
Housing and base are made of stainless steel. Non-clog
composite impeller, ceramic shaft facing, and oil chamber
for seal lubrication. Motor casing, shaft, and external hard-
ware are stainless steel.
SPECIFICATIONS
Power supply required ...................................115V, 60 HZ.
Liquid Temp. Range ....................................32° F to 130° F
Dedicated Circuit Requirement (minimum) ..........15 Amps
Pump Discharge..............................................1-1⁄4" MNPT
Discharge Adapters: ...............................................1" FNPT

UNPACKING AND INSPECTION

Handle with care. Check items received against packing
list to be sure that all equipment has been received.
Inspect for shipping damage. If found, file claim with
carrier immediately.
GENERAL SAFETY INFORMATION
READ AND FOLLOW SAFETY INSTRUCTIONS!
Know the pump application, limitations, and potential
hazards.
Disconnect power before servicing.
Drain all water from system before servicing.
Secure discharge line before starting pump. An unsecured
discharge line will whip, possibly causing personal injury
and/or property damage.
ELECTRICAL AND SWITCH SPECIFICATIONS
Model
FPSS1200X
PERFORMANCE
Model HP
FPSS1200X 1/4
For parts or assistance, call Flotec Customer Service at
3/4" Hose
Motor
Full Load
HP Amps
1/4 2.5
5'
19.0
Check hoses for weak or worn condition before each use,
making certain that all connections are secure.
Periodically inspect pump and system components. Keep
free of debris and foreign objects.
NOTICE: Not designed for applications involving salt
water or brine! Use with salt water or brine will void war-
ranty.
Personal Safety:
1. Wear safety glasses at all times when working with
pumps.
2. Keep work area clean, uncluttered, and properly light-
ed – replace all unused tools and equipment.
3. Keep visitors at a safe distance from work area.
4. Make workshop child-proof – with padlocks, master
switches, and by removing starter keys.
When wiring an electrically driven pump, follow all elec-
trical and safety codes that apply.
This equipment is only for use on 115 volt (single phase)
and is equipped with an approved 3-conductor cord and
3-prong, grounding-type plug.
To reduce risk of electric shock, pull plug
before servicing. This pump has not been investigated for
use in swimming pool and marine areas. Pump is supplied
with a grounding conductor and grounding-type attach-
ment plug. Be sure it is connected only to a properly
grounded grounding-type receptacle. Where a 2-prong
wall receptacle is encountered, it must be replaced with a
properly grounded 3-prong receptacle installed in accor-
dance with codes and ordinances that apply.
All wiring should be performed by a qualified electrician.
Make certain power source conforms to requirements of
your equipment.
Protect electrical cord from sharp objects, hot surfaces, oil,
and chemicals. Avoid kinking cord. Replace or repair
damaged or worn cords immediately.
Do not handle pump or pump motor with wet hands or
when standing on wet or damp surface, or in water.
Do not use this pump in a fish pond.
RPM
3450
GPM of Water @ Total Feet of Lift
10' 15'
13.8 8.8
1-800-365-6832
Minumum Pumps
Circuit Required Down
(Amps) To
15 1/8
Maximum
20'
4.0
2
"
Lift
23'