Elkay DSBWCT1 Manual De Instalación, Cuidado Y Uso página 8

Service: Inspection/Cleaning
This machine has been disinfected prior to departing from the factory. The dispenser needs to be cleaned prior to installing a full bottle of water.
WARNING
• To avoid any accidents, cut off the power supply before operation, as instructed below.
• The dispenser heats water to a temperature of approximately 85°C. It can cause severe burns. Disconnect electrical power prior to any
maintence operation.
1. Cleaning and draining instructions:
• Before cleaning, make sure the power switch is in the O (off) positon and unplug the water dispenser.
• Vertically insert the bottle into the supporter on top of the machine.
• Open the taps, letting about 1 liter of water flow into a container.
• Remove the water bottle from the dispenser.
• Place a large bucket beneath the drain outlet. Remove the drain cover and allow the water to drain.
• After draining, replace the drain cover and you can use the machine.
2. Sanitizing: The machine should be disinfected with the disinfectant separately purchased from a drugstore or grocery store in accordance
with the instruction manual of the disinfectant and then cleaned with water (see "Cleaning and draining instructions:"). Generally, this should
be done every three months.
3. To remove mineral deposits: Mix 4 liters of water with 200g citric acid crystals. Inject into the machine and make sure the water can flow out of
the hot water tap. Switch on the power and heat it for about 10 minutes. 30 minutes later, drain off the liquid and clean it with water two or three
times. Generally, this should be done every six months. To avoid danger from damaging the machine, never disassemble the machine by yourself.
4. Keep this machine in a dry and cool place and avoid direct sunshine. The back of the machine should be at least 10 inches away from
the wall. Never put the machine on paper or foam, which may store water and then cause creepage. Never put anything flammable next to the
machine. Do not use the machine outdoors or in a place that can be splashed by water.
5. In case of the machine not being use for a long time, turn off the heating switch of the refrigeration switch to save power.
6. In case the machine is not needed for a long time, remove the plug, turn off the copper chrome plated ball valve and drain off the remaining
water through the outlet. For another use, discharge water for 3-5 min. In the event that the machine is blocked by ice due to environmental
conditions below freezing point, keep the refrigeration switch closed for 4 hours and them turn it on to continue the operation.
7. In case the water supply is cut off, please close the feed water ball valve and cut off the power. After water re-supply, please open the other
faucets to discharge sediment and them turn on the feed water ball valve.
8. The machine must use an earthed three-pin socket and a reliable creepage protection switch.
9. Never use organic solvents such as gasoline to clean the machine; we strictly prohibit washing the machine with water or splashing water
on the machine.
10. Never turn on/off the machine by inserting the plug into (or pulling the plug out from) the socket. To avoid fire, never increase the length
of the supply cord.
11. If the supply cord is damaged, it must be replaced by the manufacturer or qualified person so as to avoid a hazard.
12. Never dismantle spare parts of the machine to avoid water leakage or damage.
13. Never turn the machine upside down or lean it more than 45° when moving it so as to avoid any damage to it or any accident.
Troubleshooting
Water is leaking.
• Unlplug dispenser, remove bottle and replace it.
No water is coming from the spout.
• Make sure the bottle is not empty. If empty, replace it.
• Make sure to completely depress the pushbutton controls.
Cold water is not cold.
• It takes up to one hour after setup to dispense cold water.
• Make sure the power cord is properly connected to a working outlet
• Make sure the back of the dispenser is at least 4 inches from a wall and there is free airflow on all 4 sides of the dispenser
• Make sure green power switch on back of dispenser is ON.
Hot water is not hot.
• It takes 15-20 minutes after setup to dispense hot water.
• Make sure the power cord is properly connected to a working outlet.
• Make sure red power switch on back of dispenser is ON.
Dispenser is Noisy.
• Make sure the dispenser is positioned on a level surface.
1000003280 (Rev. B - 02/16) Page 8