The Water Tank; After Use; Storage; Maintenance - Morphy Richards 47507 Manual De Instrucciones

VC70495MEE Rev4_9225 47507 MEE pump - Jon 25/01/2014 15:12 Page 8
1 2 Utility nozzle (27) once attached to the accessory adaptor (22), the
utility nozzle is the base attachment for attaching all the following
accessories:
• Elasticated utility cloth (28) for covering the utility nozzle when
cleaning upholstery and bedding.
1 3 Squeegee attachment (29) can be attached to the utility nozzle by
inserting the hooks at the back of the squeegee nozzle into the
loops on the back of the utility nozzle, then secure the front of the
utility nozzle into the locking clip on the top of the squeegee
nozzle (as shown).
• Remove the squeegee after use by holding the locking clip
forward. The utlity nozzle should still be hooked into the loops on
the rear of the squeegee nozzle, pivot the utility nozzle up and
unhook from the loops to lift it away.
1 4 The squeegee nozzle is ideal for cleaning tiled or glass areas such
as windows or mirror panels. To clean windows, start at the top,
press the squeegee to the surface and drag downwards in
straight passes from top to bottom. Wipe the rubber blade and
the bottom edge of the window dry after each pass. For small
window panels, remove the squeegee tool and spray the steam
directly onto the surface. Use the squeegee separately to wipe
away the moisture.
WARNING: Do not use on very cold glass, as the sudden
temperature change may crack the glass.
• Mini cleaning head (30) with mini cleaning cloth (31) attached
attaches to the utility nozzle (using the same method as attaching
and unattaching the squeegee nozzle, as shown on the left and
above). This accessory is useful for cleaning tiled or glass
surfaces, cabinets and worktops in kitchens and bathrooms, plus
upholstery, curtains, blinds, pillows and mattresses.

The water tank

The brass ball weight (16)
The brass ball weight inside the water tank is attached to the end
of the suction hose. The ball is weighted and designed to freely
move around the water tank depending on the position of the
product. The ball must remain in the water so steam can be
generated whenever the steam trigger is pressed regardless of the
orientation of the hand-held steamer.
Rinsing the water tank
Regularly rinse the water tank to release any deposits that have
collected on the bottom of the tank. Only use de-ionised,
demineralised or distilled water (available from most large
supermarkets) and fit the filler cap to allow vigorous rinsing.

After use

Follow the two maintenance steps below after every use.
1 Switch the cleaner off and unplug from the socket. Place
immediately on a suitable surface (eg. tiled floor) where the
residual heat/moisture in the floor nozzle/cloth will not affect the
surface. Wait until the cleaner has cooled down completely.
2 Empty the water tank (14) by removing the filler cap (11) and
pouring out the water. Allow the inside of the water tank to dry out
before replacing the filler cap.
8

Storage

1 6
Wrap the cord around the two cord storage hooks (4/5), rotating
the upper storage hook (4) upwards to secure the power cord (10)
in place.
Put all accessories into the accessory bag (32) and hang the bag
from the upper cord storage hook.

Maintenance

WARNING: Always unplug the Steam cleaner from the mains
supply before undertaking any maintenance procedures.
Overall maintenance
Your cleaner is manufactured to withstand normal day-to-day use,
but an occasional wipe over with a damp cloth will help maintain
it. Abrasive cleaners should not be used.
Cleaning the cloths
The floor cloth (20) and the elasticated utility cloth (28) can all be
machine washed (30ºC max). For heavy soiling, soak the cloths in
warm water and detergent or a mild stain remover.
IMPORTANT: Do not use bleach or fabric softener.
Allow to completely dry before storing.
Contact our helpline to purchase replacement cloths.
Maintaining the attachments
Dirt and blockages should be regularly removed from the
attachments to help prolong their usage.

Contact us

Helpline
If you are having a problem with your appliance, please call our
Helpline, as we are more likely to be able to help than the store
you purchased the item from.
Please have the product name, model number and serial number
to hand when you call to help us deal with your enquiry quicker.
UK Helpline: 0844 871 0960
IRE Helpline: 1800 409 119
Spares: 0844 873 0726
TalkTo Us
If you have any questions or comments, or want some great tips
to help you get the most out of your products, join us online:
Blog: www.morphyrichards.co.uk/blog
Facebook: www.facebook.com/morphyrichardsuk
Twitter: www.twitter.com/loveyourmorphy
Website: www.morphyrichards.com