Dust/Chip Extraction - Bosch GOP 10,8 V-LI Professional Instrucciones De Servicio

Operating instructions
Mount the requested application tool/accessory
(e. g. plunge cut saw blade 9 ) in such a manner
on the tool holder 8 that the offset faces down-
ward (see illustration on the graphics page;
marking on the application tool/accessory is
readable from above).
Turn the application tool/accessory to a position
favourable for the respective job, and allow it to
engage into the cams of the tool holder 8 . 12 dif-
ferent positions are possible, each offset by 30°.
Fasten the application tool/accessory with bolt
10 . Tighten the bolt with Allen key 11 until the
spring washer of the bolt faces flush against the
application tool/accessory.
e
Check the tight seating of the application
tool/accessory. Incorrect or not securely fas-
tened application tools/accessories can co-
me loose during operation and pose a ha-
zard.
Mounting/Replacing a Sanding Sheet on the
Sanding Plate
The sanding plate 12 is fitted with Velcro back-
ing for quick and easy fastening of sanding
sheets with Velcro adhesion.
Before attaching the sanding sheet 13 , free the
Velcro backing of the sanding plate 12 from any
debris by tapping against it in order to enable
optimum adhesion.
Position the sanding sheet 13 flush alongside
one edge of the sanding plate 12 , then lay the
sanding sheet onto the sanding plate and press
firmly.
To ensure optimum dust extraction, pay atten-
tion that the punched holes in the sanding sheet
match with the holes in the sanding plate.
To remove the sanding sheet 13 , grasp it at one of
the tips and pull it off from the sanding plate 12 .
You can use all sanding sheets, fleece pads/pol-
ishing cloth pads of the Delta 93 mm series of
Bosch accessory program.
Sanding accessories, such as fleece pads/pol-
ishing cloth pads, are attached to the sanding
plate in the same manner.
Robert Bosch Ltda.
Book_Pag2ate35.indb 31

Dust/Chip Extraction

e
Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one's health. Tou-
ching or breathing-in the dusts can cause al-
lergic reactions and/or lead to respiratory in-
fections of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in
connection with wood-treatment additives
(chromate, wood preservative). Materials
containing asbestos may only be worked by
specialists.
— Use dust extraction whenever possible.
— Provide for good ventilation of the work-
ing place.
— It is recommended to wear a P2 filter-
class respirator.
Observe the relevant regulations in your
country for the materials to be worked.
Connecting the Dust Extraction (see figure A)
For sanding, always connect dust extraction.
Remove the application tool/accessory when
mounting the dust extraction 17 (accessory).
If required, assemble the parts of the dust ex-
traction 17 as shown in the figure. Position the
assembled dust extraction onto the machine via
the tool holder 8 . Turn the dust extraction in
such a manner that the cams of the dust extrac-
tion engage into the corresponding recesses on
the housing. Fasten the dust extraction to the
machine with the retaining clip 15 as shown in
the figure.
Pay attention that the felt ring 14 is undamaged
and faces tightly against the sanding plate 12 .
Replace a damage felt ring immediately.
Depending on machine version, place a vacuum
hose 18 (accessory) either directly onto the vac-
uum connection 16 or cut off the old hose end,
screw the extraction adapter 19 (accessory) on-
to the hose end and then place it directly onto
the vacuum connection 16 . Connect the vacuum
hose 18 with a vacuum cleaner (accessory). An
overview for the connection of various vacuum
cleaners can be found on page 4.
en | 31
F 000 622 274 | 12.2008
18.12.08 15:46:53