SUNTEC YOG-8588 digital Manual De Instrucciones página 13

•
Operation:
Place the device in a place where room temperature (approx. 20°C) and no draughts prevail
o
during operation. Please make sure that the filled jars and the yoghurt maker filled with the jars
are not moved too much during the entire preparation time. Shocks can affect the result so the
yoghurt may not solidify otherwise.
Carefully place your filled and screwed jars in the yoghurt maker and place the lid on the device.
o
The unit must never be used without a lid, otherwise the heat will escape.
Please connect the device to the power supply. An acoustic signal sounds and the display
o
shows"- -". Each further operation on the control panel is accompanied by an acoustic signal.
Press the on/off key. "00" appears on the display, see fig. 1.
o
Press the function key as shown in fig. 2. "F1" appears on the display for yoghurt preparation.
o
To set the time, press either the "+" or "-" button to display the preset time of 8 hours. You can
o
now set the time between 1 and 24 hours using the "+" and "-" buttons. Each press increases
or decreases the value by one hour. For our recommended yoghurt recipe, please increase the
time from 8 to 11 hours.
Press the "+" and "-" keys simultaneously to set the temperature. The display shows the preset
o
temperature of 42°C. Please change the temperature to 45°C and press the on/off button to
start the yoghurt making.
When switched on, the yoghurt maker starts to heat up the glasses and their contents to keep
o
them at a constant temperature of approx. 45°C. Yoghurt cultures need the heat for a long time
to convert the milk into yoghurt. The display shows the remaining time.
To shorten the time, you can add warm water to surround the glasses with max. 1-2cm height.
o
You can also add water if the ambient temperature is less than 20°C.
When the time is over, an acoustic signal sounds and the preparation process is finished. Press
o
the on/off button to turn off the unit and unplug the power cord.
Please remove the glass containers from the yoghurt maker and place them directly in the
o
refrigerator for at least 3-4 hours to increase the firmness of the yoghurt. Please do not let the
yoghurt cool down at room temperature, otherwise the yoghurt may become sour.
Tip: If the yoghurt has not reached the desired consistency after 11 hours, you can continue the
o
preparation by putting the device back into operation. Select a shorter time setting, e.g. 2-3
hours. Please note that the preparation process can only be continued if the yoghurt has not
been cooled in the meantime. If you have pressed the on/off button by accident before
completing the settings, remove the device from the power supply and start the operation again.
Making of natto (F2)
•
Preparation:
For the preparation of natto you will need a low bowl made of glass or stainless steel which can
o
be placed into the device, soybeans and natto starter culture. For the dosages, please follow
the manufacturer's instructions of your natto starter culture.
Please soak the soybeans in water for several hours, then boil or steam them until they are
o
cooked. Put the soybeans in the bowl and let them cool to room temperature.
Please add the natto starter culture and mix it with the soybeans.
o
•
Operation:
Place the bowl in the device and put on the lid. Natto requires moisture and oxygen during the
o
fermentation process. The container must therefore not be hermetically sealed.
Connect the device to the power supply. An acoustic signal sounds and the display shows"- -".
o
Each further operation on the control panel is accompanied by an acoustic signal.
Please press the on/off key. "00" appears on the display.
o
Press the function key twice so "F2" appears for preparing natto.
o
To set the time, press either the "+" or "-" button to display the preset time of 18 hours. The
o
temperature can be set by pressing both buttons simultaneously.
Press the on/off button to start the preparation. The display shows the remaining time.
o
When the time is over, an acoustic signal sounds and the preparation process is finished. Please
o
press the on/off button to turn off the unit and unplug the power cord. Remove the bowl from
the device.
The finished natto can be stored airtight in the refrigerator.
o
Making of kimchi (F3)
•
Preparation:
For the preparation of kimchi you need Chinese cabbage, spices of your choice, kimchi starter
o
culture as well as a low, airtight sealable container, which can be put into the device. For the
dosages, please follow the manufacturer's instructions of your kimchi starter culture.
Fig. 1 Fig. 2