Motive NEO-WIFI Manual Tecnico página 129

50 R/W start[3]
51 R/W stop[3]
52 R/W start[4]
53 R/W stop[4]
54 R/W enable starts timer
55 R/W save parameters
56 R/W reset factory data
57 R/W sensor minimum value
58 R/W sensor maximum value
59 R/W pressure range
60 R/W pressure reference
61 R/W pressure hysteresis
62 R/W delay time to stop when pressure is reached
63 R/W alarm saved
64 R alarm type
65 R time intervention alarm h
66 R time intervention alarm I
67 R voltage during alarm intervention [V12]
68 R voltage during alarm intervention [V13]
69 R voltage during alarm intervention [V23]
70 R current during alarm intervention [I1]
71 R current during alarm intervention [I2]
72 R current during alarm intervention [I3]
73 R power during alarm intervention
74 R voltage capacitors during alarm intervention
75 R frequency during alarm intervention
76 R
power factor cosϕ during alarm intervention
77 R rpm during alarm intervention
78 R IGBT temperature during alarm intervention
79 R /W pre-heating temperature
80 R momentary value rpm/bar
81 R power
82 R current
83 R voltage
84 R IGBT temperature
85 R power factor cosϕ
129/137
minuti 0
minuti 0
minuti 0
minuti 0
0
0
0
mA*10 0
mA*10 100
bar*1000 (Ventilation)
bar*100 (Air Compressor) 69
bar*10 (HP pump)
bar*1000 (Ventilation)
bar*100 (Air Compressor) 69
bar*10 (HP pump)
bar*1000 (Ventilation)
bar*100 (Air Compressor) 1
bar*10 (HP pump)
seconds 1
0
1
seconds*0x10000 0
seconds 0
V -
V -
V -
A*10 -
A*10 -
A*10 -
W -
Vdc -
Hz -
*100 -
rpm -
°C -
°C 0
rpm (speed)
bar*1000 (Ventilation)
-
bar*100 (Air Compressor)
bar*10 (HP pump)
W -
A*10 -
V -
°C -
*100 -
NEO-WiFi – manual - ES
to calcolate the value: hours*60+minutes
1439 (if there are problems during calculation, please download the
spreadsheet automatically from www.motive.it)
to calcolate the value: hours*60+minutes
1439 (if there are problems during calculation, please download the
spreadsheet automatically from www.motive.it)
to calcolate the value: hours*60+minutes
1439 (if there are problems during calculation, please download the
spreadsheet automatically from www.motive.it)
to calcolate the value: hours*60+minutes
1439 (if there are problems during calculation, please download the
spreadsheet automatically from www.motive.it)
1 0=OFF, 1=ON
to save the parameter, write 1 and next 541 (wait until it returns to 0 to
541
confirm receipt)
to reset the factory data write 1 (Standard) or 2 (Ventilation) or 3 (Air
541 Compressor) or 4 (HP pumps), and then 541 (wait until it returns to 0 to
confirm receipt)
100
300
16000
Par.103
200
99
it shows the last alarm saved, or the alarm corresponding to the
6539
number written
29 type of last alarm recorded
0xffff
0xffff
-
-
-
-
-
-
-
-
-
-
-
-
50
- average value, measured in about 0,5 seconds
- average value, measured in about 0,5 seconds
- average value, measured in about 0,5 seconds
- average value, measured in about 0,5 seconds
- average value, measured in about 0,5 seconds
- average value, measured in about 0,5 seconds
REV18-GEN20