Sound Level; Vibration Level; Ec Marking Of The Shears - Jacto PR-40 Manual De Instrucciones

Technical data battery:
Description
Type
Battery voltage
Battery capacity
Battery weight
Cutting autonomy
Battery charging time
Electronic protections
Time auto power-off for
inactivity
Thermal protection

1.9. Sound level

The air noise level created by the Shears under operating con-
ditions was detected using a sound level meter with integrator.
The measurements were carried out in accordance with EN ISO
3746-2010. Tests performed under the conditions indicated by
the standard produced the following results:
• Equivalent weighted sound pressure average level: LpAm
= 60,2 dB(A).
• Sound power level: LwA = 71,8 dB(A).
• Sound pressure level at operator's station: LpA = 60,6 dB(A).

1.10. Vibration level

The level of vibrations transmitted to the operator's hand-
arm system by the Shears in operating conditions has been
measured, in compliance with standard EN ISO 20643:2008/
A1:2012.
The tests have given the following results:
• No-load operation: weighted RMS value measured on the
handle of the shears: a
• Load operation: weighted RMS value measured on the
handle of the shears: a

1.11. EC marking of the shears

Directive 2006/42/EC specifies the minimum conditions with
which a machine can be placed on the EU market. All machines
can only be marketed and put into service if the health and
safety of persons, domestic animals or property are not affect-
ed. The Shears does not fall under one of the machine cate-
gories indicated in the list set out in Annex IV of the Directive
(particularly dangerous machinery).
30/69
Unit of Value
measure Battery
- Li-Ion rechargeable
V 50,4
mAh 4400
g 2800
- max 2 days
h 6
Overexertion and
-
short-circuit
min (after) 10 min
- Overheating
heq
= 0.53 m/s².
heq
= 1.55 m/s².
In order to certify the conformity of the machine with the pro-
visions of Directive 2006/42/EC, before placing the product on
the market, the manufacturer applied the procedure described
in Art. 5. In this sense, the manufacturer has provided for: com-
pliance with the relevant safety requirements; availability of
the technical file as stipulated in Annex VI; implementation of
all the tests and inspections required by the reference stan-
dards and compliance with the essential health and safety
requirements indicated in Annex I of the Directive itself. The
construction technical file, which contains the basic project in-
formation and all the characteristics related to machine safety,
was drafted in accordance with the provisions of Annex VI-Part
A, and can be made available by the individual indicated in the
CE Declaration of Conformity for any verification carried out
by the supervisory authorities, following a justified request, as
provided for by the relevant laws in force.
Once the manufacturer has verified that the machine has been
designed and built in accordance with the provisions of Direc-
tive 2006/42/EC and that it can be used safely in the service
conditions specified in this manual, it places the Shears on the
market and accompanies the machine with:
• Usage instructions booklet (User manual)
• EC Declaration of conformity
• EC Marking
In designing and manufacturing the Shears, the manufacturer
has complied with obligations resulting from applying related
European legislative provisions and precisely the following Eu-
ropean provisions:
• Directive 2006/42/CE (Machinery safety).
• Directive 2004/108/EC (Electromagnetic compatibility).
• Directive 2006/95/EC - (Low voltage).
For verification of conformity to European legislative provi-
sions indicated above, the manufacturer applied the following
European standards and technical rules:
EN 349:1993+A1:2008: MACHINERY SAFETY - Minimum dis-
tance to keep from crushing human body parts.
• EN 1037:1995+A1:2008: MACHINERY SAFETY - Prevent-
ing unexpected start-up.
• EN ISO 3746:2010: ACOUSTICS - Determining the sound
power levels of sources using sound pressure - Control
method on a reflecting surface by measuring an envel-
oping surface.
• ISO 7000:2012: GRAPHICAL SYMBOL FOR USE ON EQUIP-
MENT - Registered symbols.
• EN ISO 11202:2010: ACOUSTICS - Noise emitted by
machinery and equipment - Determination of emission
sound pressure levels at a work station and at other
specified positions - Site control method.
• EN ISO 12100:2010: MACHINERY SAFETY - Basic concepts,
general principles for design.
• EN ISO 13524:2009: Machines for road maintenance -