Virutex MEB250 Manual De Instrucciones página 6

5.1 FITTING THE REAR GUIDE PLATE
Insert an arm (E, Fig. 1) in each of the two guides (G,
Fig. 1) attached to the sides of the table.
Remove the screws (C, Fig. 1) and the washers (B,
Fig. 1) from the arms (E, Fig. 1).
Mount the rear support bar (A, Fig. 1) on the arms E,
and fix it to the supports (D, Fig. 1) using the screws
(C, Fig. 1) and the washers (B, Fig. 1).
Move the rear guide plate into the guides (G, Fig.
1) until it touches the bar (H, Fig. 1) of the table.
Fix the rear support guide in this position with the
levers (I, Fig. 1) on both sides.
Loosen the screws (C, Fig. 1); make the surfaces of
the rear support bar (A, Fig. 1) flush with the bar (H,
Fig. 1) on the table and tighten the screws (C, Fig.
1) in this position.
5.2 FITTING EDGEBANDER PEB200/PEB250
TO THE TABLE
Place the edgebander PEB200 or the edgebander
PEB250 on the table MEB250 in the position shown
in (Fig. 2) and fasten it with the three screws (J, Fig 2).
5.3 FITTING EDGEBANDER PEB50/PEB150
TO THE TABLE
Remove the screws (IO, Fig. 6) to remove the guide (IN,
Fig. 6). Place the edgebander PEB50 or the edgebander
PEB150 on the table MEB250 in the position shown
(Fig. 2) and fasten it with the three screws (J, Fig. 2).
Replace the guide (IN, Fig. 6) in the same place. To
remove the edgebander PEB50/PEB150, you must
once again remove the guide (IN, Fig. 6).
6. PREPARING EDGEBANDER PEB200/PEB250
Follow the steps indicated in the PEB200/PEB250
edgebander manual exactly to prepare it for gluing
the first edging.
The steps to take in chronological order are listed
below as a reminder:
• Connect the PEB200/PEB250 edgebander to the
power source.
• Turn on the main switch (IG, Fig. 2) depending on
the model, to begin warm-up.
• Cut the edging strip to the measurement of the
board to be glued.
• Adjust the edging guide heights.
• Adjust the edging thickness.
Do not leave the strip in the guides. Remove
it when you have finished the adjustments.
6
PEB200
• WHEN THE LIGHT THAT INDICATES THAT THE MOTOR
IS RUNNING (IA, Fig. 2) COMES ON:
- Check there is enough glue in the machine tank.
- Check the glue flow setting is correct.
• The edgebander is now ready to start gluing edgings.
PEB250
- Set the working temperature.
• WHEN YOU HEAR A "beep-beep", THE LIGHT ON
THE CONTROL PANEL (IH, Fig. 2) WILL COME ON, AND
THE MACHINE IS READY FOR USE:
- Check there is enough glue in the machine tank.
- Check the glue flow setting is correct.
• The edgebander is now ready to start gluing edgings.
7. EDGEBANDING STRAIGHT PIECES
Prior adjustments:
Ensure that the support guides (M and L, Fig. 1) are
in the right position:
• The exiting support guide (M, Fig. 7) should be in
line with the two rollers (P and N, Fig. 7). If it is not,
you can align it by loosening the screws (R, Fig. 2)
that hold it in place.
• To check that the intake guide (L, Fig. 7) is positioned
correctly, place a piece of the strip you are going to
edgeband against the rollers (P and N, Fig. 7). Press
a straight panel against these and ensure that the
intake guide (L, Fig. 7) is in line with the clean edge
of the panel. If it is not, align it by loosening the
screws (R, Fig. 2) that hold it in place.
Place the clamp (F, Fig. 7) in position:
If you wish to edgeband with the help of the clamp
(F, Fig. 7), you will have to adjust the position of the
rear support guide (A, Fig. 7) so that the clamp exerts
some force on the outer edge of the panel, and fix
the guide in this position with the levers (I, Fig. 1).
To edgeband panels wider than 500 mm, on which
it is not possible to use the clamp, it can easily be
removed and placed upside down (F, Fig. 10) so that
it does not get lost.
Edgbanding:
If the PEB200/PEB250 edgebander is ready to band
edges, as explained in section 6, follow the steps
below to edgeband the board:
• Turn on the advance switch (IJ, Fig. 2) for the
PEB200. This is located on the handle of the machine.
Turn the handle (IK, Fig. 2) on the PEB250 only and
select the working speed.
• Wait a few seconds for the glue to rise from the
tank to the gluing roller.