Tabla De Contenido; Introduction - Eye Hortilux GRC1 Manual Del Usuario

TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1: Product Specifications . . . . . . . . . . . . . . . . . . . . . 3
1.1: Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2: Product Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3: Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4: Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.5: Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.6: Master Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2: Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3: Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4: Installing Controller . . . . . . . . . . . . . . . . . . . . . . . 6
4.1: Mounting Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.2: Installing Temperature Sensor in "Follow Mode". . . . 6
4.3: Connecting Equipment Used in Lights-off Periods . 7
4.4: Controlling Auxiliary Equipment in "Inverse Mode". 8
4.5: Connecting Controller to Ballasts. . . . . . . . . . . . . . . . . . 8
4.6: Connecting Controller to Complete Systems. . . . . . . 8
4.7: Connecting Controller to Main Power Supply . . . . . . 8
5: Preparations Before Use . . . . . . . . . . . . . . . . . . . 9
5.1: Localizing Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2: Calibrating Temperature Sensor . . . . . . . . . . . . . . . . . . . 10
5.3: Changing Display Mode from % to Watts . . . . . . . . . . 10
Make sure you read the user manual in full before you begin operating the product.
COMPLETE LIGHTING CONTROL AT YOUR FINGERTIPS
Using an EYE HORTILUX® master controller for your EYE HORTILUX® systems offers you maximum control,
ease of use, safety and plug-and-play installation. Just connect the controller cables to the systems with the
T-splitter included with the system (see Figure 5), set the dials on the systems to EXT (External control), plug
the controller and the systems directly into the main power supply and you are set to go.
The EYE HORTILUX GRC1 controller can switch all the interconnected systems on and off with its internal
timer, adjust them to your required output level (in percentage or exact output power) and even simulate
sunrise and sunset to gradually adjust the climate in your grow room when your lights go on or off. This
electronic controller replaces expensive lighting timers and electrical contactors while preventing ballast
current in-rush when switching on your lights.
Two very important features of the EYE HORTILUX GRC1 controller are the auto-dim function and
emergency shut-down. When the temperature in your grow room rises above the control level of your
climate control, your crop can be damaged beyond recovery. The temperature probe senses this and will
automatically dim the system until the desired temperature is achieved.
The controller can also manage your lights to maintain a safe temperature utilizing the included
temperature sensors. The display and warning LED indicate when high temperatures are reached and
also indicate if this has happened while you were away. If for any reason your climate control completely
fails and the temperature rises to unacceptable levels, the EYE HORTILUX GRC1 controller will perform an
emergency shutdown of all connected equipment. The alarm contact of the controller can be connected
to your alarm system for instant notification.
You can connect up to one-hundred systems to one controller and control two separate rooms (up to 50
systems each) using their own temperature sensor for auto-dim (at high temps) and emergency shutdown
(at extreme temps).
For auxiliary equipment, you can connect up to two accessories via the EEM port, one to switch equipment
when lights are on (e.g. a humidifier, CO
a room heater).
2
equipment or air conditioning) and one when lights are off (e.g.
2
Visit eyehortilux.com for the latest installation instructions.
6: Programming and Using the Controller . . . . . 11
6.1: Adjusting Ballast Output to Change Light Intensity 11
6.2: Control Lamp with Lower Power Rating than Ballast 11
6.3: Programming a Light Cycle . . . . . . . . . . . . . . . . . . . . . . . 11
6.4: Setting Follow or Inverse Mode (AUX Function) . . . . 12
6.5: Setting Temperature Safety Settings. . . . . . . . . . . . . . . 12
6.6: Setting the Auto-dim Temperature . . . . . . . . . . . . . . . . 12
6.7: Setting Safety Shutdown Temperature . . . . . . . . . . . . 12
6.8: Setting the Sunrise and Sunset Period . . . . . . . . . . . . . 13
6.9: Activate/Deactivate Systems Manually/Automatically 13
6.10: Resetting Controller to Factory Settings . . . . . . . . . . 13
7: Interpreting Controller Information . . . . . . . . . 14
7.1: Reading the Default Screen . . . . . . . . . . . . . . . . . . . . . . . 14
7.2: Showing System Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.3: Interpreting LED Signals . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.4: Interpreting Display Messages . . . . . . . . . . . . . . . . . . . . 15
8: Maintenance, Repair and Disposal . . . . . . . . . . 15
9: Display Screens Overview . . . . . . . . . . . . . . . . . . 16
French . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-30
Spanish . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-43