Intended Use - PLYMOVENT DRAFTMAX BASIC Manual De Instalación Y De Manejo

cover of this document and any corresponding accessories.
Specific working conditions or used accessories may require
additional safety instructions. Immediately contact your
supplier if you detect a potential danger when using the product.
The user of the product is always fully responsible for
observing the local safety instructions and
regulations.
User manual
- Everyone working on or with the product, must be familiar
with the contents of this manual and must strictly observe the
instructions therein. The management should instruct the
personnel in accordance with the manual and observe all
instructions and directions given.
- Never change the order of the steps to perform.
- Always keep the manual with the product.
Pictograms and instructions on the product (if
present)
- The pictograms, warning and instructions attached to the
product are part of the safety features. They must not be
covered or removed and must be present and legible during
the entire life of the product.
- Immediately replace or repair damaged or illegible
pictograms, warnings and instructions.
Users
- The use of this product is exclusively reserved to well
authorised, trained and qualified users. Temporary personnel
and personnel in training can only use the product under
supervision and responsibility of skilled engineers.
1

Intended use

The product has been designed as a workbench with integrated
extraction and filtration facility for welding and grinding
purposes, provided the appropriate options have been installed
(refer to section 2.3). With the optional HEPA set the product is
suitable to extract welding fume from high alloyed steel, i.e.
steel with a nickel and chromium content of >30%. This
corresponds with welding fume class "W3". Using the product for
other purposes is considered contrary to its intended use. The
manufacturer accepts no liability for any damage or injury
resulting from such use. The product has been built in
accordance with state-of-the-art standards and recognised
safety regulations. Only use this product when in technically
perfect condition in accordance with its intended use and the
instructions explained in the user manual.
Technical specifications
The specifications given in this manual must not be altered.
Modifications
Modification of (parts of) the product is not allowed.
Use
WARNING!
Never use the downdraft table without spark
arresters, main filter cartridges and dust drawers.
1. "Intended use" as explained in EN-ISO 12100-1 is the use for which
the technical product is suited as specified by the manufacturer,
inclusive of his directions in the sales brochure. In case of doubt it is
the use which can be deducted from the construction, the model and
the function of the technical product which is considered normal use.
Operating the machine within the limits of its intended use also
involves observing the instructions in the user manual.
0507060400/151013/G DraftMax Basic | DraftMax Advance | DraftMax Ultra
WARNING
Fire hazard! Never use the product for:
- filtering flammable, glowing or burning particles or
solids or liquids
- filtering of aggressive fumes (such as hydrochloric
acid) or sharp particles
- sucking cigarettes, cigars, oiled tissues, and other
burning particles, objects, and acids
WARNING
Never use the product for:
- oxy-fuel cutting
- arc-air gouging
- oil mist
- paint mist
- heavy oil mist in welding fume
- extraction of hot gases (more than 45°C/113°F
continuously)
- grinding aluminium and magnesium
- flame spraying
- extraction of cement, saw dust, wood dust etc.
- explosive environments or explosive substances/
gases
ATTENTION!
In case of welding and plasma cutting, the use of a
backdraft kit is required.
- Inspect the product and check it for damage. Verify the
functioning of the safety features.
- Check the working environment. Do not allow unauthorised
persons to enter the working environment.
- Protect the product against water and humidity.
- Use common sense. Stay alert and keep your attention to your
work. Do not use the product when you are under the
influence of drugs, alcohol or medicine.
- Make sure the room is always sufficiently ventilated; this
applies especially to confined spaces.
- Never install the product in front of entrances and exits which
must be used for emerency services.
- Make sure that the workshop, in the vicinity of the product,
contains sufficient approved fire extinguishers.
- Air containing particles such as chromium, nickel, beryllium,
cadmium, lead etc., which is a health hazard, should never be
recycled. This air must always be brought outside the working
area, unless the optional HEPA kit has been installed.
Service, maintenance and repairs
- Observe the maintenance intervals given in this manual.
Overdue maintenance can lead to high costs for repair and
revisions and can render the guarantee null and void.
- Always use tools, materials, lubricants and service techniques
which have been approved by the manufacturer. Never use
worn tools and do not leave any tools in or on the product.
- Safety features which have been removed for service,
maintenance or repairs, must be put back immediately after
finishing these jobs and it must be checked that they still
function properly.
WARNING!
After switching off the fan, wait at least 20 seconds
before opening the door(s) to carry out service,
maintenance or repair jobs.
ATTENTION!
Always wear face mask and gloves during filter
exchange/cleaning.
ATTENTION!
Industrial vacuum cleaner used during service and
maintenance should meet dust class H according to
EN 60335-2-69.
EN - 6