Publicidad
Idiomas disponibles
Idiomas disponibles
Connecting Regulator To The
LP Tank
Only use the pressure regulator &
hose supplied with this appliance. See
assembly instructions or appliance
name tag for regulator model
number.
1. Place
LP
tank
on
a
secure,
level,
and
stable
surface.
2. Turn control knob
to the OFF position.
3. Turn LP tank OFF by turning hand
wheel clockwise to a full stop.
4. Remove the protective cap from
LP tank valve. Always use cap and
strap supplied with valve.
Do not use a POL
transport
plug
(plastic part with
external threads)!
It will defeat the
safety feature of
the valve.
(B) Nipple has to
be centered into
the LP tank valve
(C) Hold coupling
nut and regulator
as
shown
proper connection
to LP tank valve
0312-Coven-TriBook.indd 10-11
5. Hold regulator, insert nipple (B)
into LP tank valve. Hand tighten
coupling nut, holding regulator in
a straight line (C) with LP tank
valve so as not to cross thread the
connection.
6. Turn the coupling nut clockwise
to tighten to a full solid stop. The
regulator will seal on the back-check
feature in LP tank valve, resulting in
some resistance. An additional one-
half to three quarters turn is required
to complete connection. Tighten by
hand only – do not use tools.
NOTE:
If you cannot complete
connection, disconnect regulator and
repeat steps 5 and 6. If you are still
unable to complete the connection,
do not use this regulator!
• Do not insert any foreign objects into
the valve outlet. You may damage
the valve and cause a leak. Leaking
propane may result in explosion, fire,
severe personal injury, or death.
• Never attempt to attach this appliance
to the self-contained LP gas system of
a camper or trailer or motor home.
Leak Testing Valves, Hoses and
Regulator
1. Turn all control knob(s) to OFF.
2. Be sure regulator is tightly connected
to LP tank.
3. Completely open LP tank valve
by turning hand wheel counter
clockwise. If you hear a rushing
sound, turn gas off immediately.
There is a major leak at the connection.
Correct before proceeding.
for
4. Brush
soapy
solution
onto
i n d i c a t e d
c o n n e c t i o n s
shown at right.
5. If "growing" bubbles appear,
there is a leak.
Close LP tank
valve immediately and retighten
connections.
If leaks cannot be
stopped, do not try to repair. Call
for replacement parts. Order new
parts by giving the serial number,
model number and name of items
needed to the Service Center at
1-435-752-3922.
6. Always close LP tank valve after
performing tank leak test by turning
hand wheel clockwise.
WARNING
• Do not use appliance until leak
checked.
• If you cannot stop a gas leak,
immediately close LP tank valve
and call LP gas supplier or your
fire department!
Setup Instructions:
• Setup the oven on a level surface.
• Open the lid and attach the
windscreens to the side of the oven
as shown.
• Make sure the pot grate is installed
properly with the wire ends fitting
into the holes on the top of the oven
to prevent the rack from moving (See
Picture)
Lighting Stove Instructions:
Do not lean over the Oven while
lighting.
1. Remove all appliances from the
burner to create a free flow or air.
2. Open lid - Do not attempt to light
the stove with the lid closed.
3. Fully open LP bottle valve if using a
bulk tank.
4. Turn control valve slowly to the High
position. Cooker will ignite. Adjust
controls to desired temperature.
5. If ignition does not occur in 5
seconds, turn the burner control(s)
off, wait 5 minutes, and repeat
lighting procedure. If built-in ignitor
will not light follow the preceding
steps and hold a lit long igniter
or match next to the burner when
opening the control valve.
Lighting Oven Instructions:
Do not lean over the Oven while
lighting.
1. Remove all appliances from the oven
to create a free flow of air.
2. Open Oven Door. Do not attempt to
light the oven with the door closed.
3. Remove the bottom oven tray to
reveal the burner.
4. Push the gas valve handle in and
turn slowly to the high position. The
Oven Burner will ignite. (If lighting
with a match, light match and place
it over the burner. Slowly turn on
the valve Do not stand with head or
arms over the burner.)
5. Keep handle depressed for 10
seconds.
6. If the burner does not stay lit repeat
the process.
7. Re-install the bottom oven tray over
the burner.
8. Adjust the controls to the desired
position.
9. If ignition does not occur in 5 seconds,
turn the burner control(s) off, wait
3/22/12 4:29 PM
Publicidad
