Ordering Information - Pima CLM302 Instrucciones De Instalación

 UG96 Approvals
o RoHS Compliant
o CE/GCF (Europe)
o DoC (Russia)
o IFETEL/Movistar (Mexico)
o ICASA (South Africa)
o Anatel (Brazil)
o Telefonica (Global)
 Sensitivity
o -110dbm@UMTS 800/850/
900/2100
o -109.5dbm@UMTS 1900
o -109.5dbm@GSM 850
o -108.5dbm@EGSM 900
o -110dbm@ DCS 1800
o -108dbm@PCS 1900
 HSUPA: Release 7 (Category 6+8)
 EDGE: Multi-slot Class 33
 GPRS: Multi-slot Class 33
 UMTS: Release 99/7
Content of the product package
 CLM302 Add-on
Antenna placement guidelines
 Have a clear line of sight to the sky (where possible)
 Be clear and free of obstacles
 Be clear of metal objects
 Be located away from other transmitting devices
 Be securely affixed in location
 Use the supplied cable
How to install the CLM302
Disconnect the control panel from AC and battery power before installing the CLM302.
Follow the next steps to install the add-on.
1. Push the eject bar (no. 8 in the above figure) using an extraction tool or pin and eject the SIM card.
2. USIM 1 (main) card into slot 4 (in the above figure), and USIM 2 (backup, if in use) card into slot 5, with the metal contacts
Align
facing downwards and the angled corner of the card positioned correctly, and carefully insert the tray into place.
3. Connect the antenna to the antenna connector (no. 6 in the above figure), by rotating the SMA connector clockwise.
4. Connect the add-on's circuit board connector (no. 11 in the above figure) to its socket on the control panel's circuit board.
5. Connect the control panel to power.
6. Locate the antenna according to the above guidelines, where the cellular signal is strong; see the FORCE's Installation guide on how
to check the reception level.
7. Set the add-on in the control panel; see how in the FORCE's Installation guide.
8. Test the add-on in the
The LEDs
The CLM302 LEDs are described in the table below.
Label Color and state
Yellow blinks (64ms On/800ms Off)
LD1 Yellow blinks (64ms On/2000ms Off)
Yellow blinks (64ms On/600ms Off)
LD2 Red
LD3 Green solid
LD4 Blue

Ordering information

 CLM302 Kit: P/N 8300045
 GSM: Release 99/4
 3GPP TS 27.007, 3GPP TS 27.005
 Enhanced AT Commands
 Bands
o 800/850/900/1900/2100MHz
o 850/900/1800/1900MHz @GSM
o HSUPA Release 7 (category 6)
o HSDPA Release 7 (category 8)
o EDGE Multi-slot Class 12
o GPRS Multi-slot Class 12
o UMTS Release 99/7
o GSM Release 99/4
 Voice
o Speech Codec Modes: HR, FR,
o Echo Arithmetic: Echo
 Electrical Characteristics
o Output Power:
 Antenna + Cable
Tests and Diagnostics menu.
Description
Modem is registered to the network
Modem is not registered to the network
Data transfer
Not in use
Power on
Used by the manufacturer
@UMTS
EFR, AMR, AMR-WB
Cancellation, Noise Reduction
 This guide
-2-
 Class 3 (24dBm +1/-3dB) for
UMTS bands
 Class E2 (27dBm±3dB) for
GSM850 & EGSM900
 Class E2 (26dBm±3dB) for
DCS1800 & PCS1900
 Class 4 (33dBm ±2dB) for
GSM 850/900
 Class 1 (30dBm ±2dB) for
GSM 1800/1900
o Power consumption
 50μA@power off
 1.1mA@GSM sleep, DRX=9
 1.7mA@UMTS sleep, DRX=9
 240mA@GSM voice (max.)
 490mA@UMTS voice (max.)
 520mA@GPRS data (max.)
 500mA@EDGE data (max.)
 580mA@HSDPA (max.)
 540mA@HSUPA (max.)