Swisher STP4422HO Manual Del Proprietário página 12

Ocultar thumbs Ver también para STP4422HO:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ITEM # PART #
1
19015*
Motor Base - Upper, STP Trimmer
2
10197
Bolt - Carriage 5/16-18X1 GR5 ZY
3
19019
Bearing - 1/2" Flange Mounted
4
10216
Bolt - Carriage 5/16-18X3/4 GR5 ZY
5
NB170
Nut - Serr Flange 5/16-18 ZY
6
NB604
Bolt - 3/8-16 X 1 GR5 ZY
7
4005
8
NB182
9
NB107
Bolt - 3/8-16 X 1 1/2 HCC GR5 ZY
10
T30V
Pulley - Idler Clutch, 2 3/4 OD
11
NB174
Nut - Jam 3/8-16 ZY Grade 2
12
19024*
Idler Arm - Transmission
13
7821
14
NB272
Washer - SAE Flat 3/8 ZY
15
NB280
Nut - 2 Way Lock 3/8-16 ZY
16
19020
Transmission - String Trimmer
17
19025
Axle - Self-Propelled Trimmer
18
26X249
19
19087*
Guard - Chain; Trimmer
20
NB501
Bolt - 5/16-18 X 1 HCC GR5 ZY
21
NB579
Washer - Fender, 5/16 X 1 1/4 OD ZY
22
16823
Bushing - Shoulder 3/8, ZT60
23
19023*
Bracket - Idler Arm, SP Trimmer
24
19053
25
NB126
26
19036
Pin - Cotter, 3/16 X 2.25; ZP
27
690369
Spacer - 1/2" TO 17 MM
28
19022
Sprocket - No. 35, 60 Teeth; 1/2" Bore
29
19035
Pin - Cotter, 1/8 X 1-1/2; ZP
30
19021
Sprocket - No. 35, 10 Teeth; 1/2" Bore
31
19044
Chain - ANSI #35, 70 Link Loop
32
MWB
Bearing - Wheel, 1 1/8"OD X 1/2"ID
33
19045***
Clutch - Wheel, 1.125 OD X 0.5 ID
34
19026**
Wheel - 14", 1/2" Bearings; Trimmer
35
NB177
Washer - Mach 1/2 NR 14 GA
Drive Train Assembly
DESCRIPTION
Bearing - Side Flange
Nut - Nyloc 3/8-16 ZY
Latch Spring
Screw - .312-18 x .75
Belt - 24", SP Trimmer
Pin - Cotter, 1/8 X 1
When ordering replacement parts
* Use paint code: TK=Black
** Wheels include two bearings. Use part # MWB when replacing bearings only.
Note: Optional wheel kits are available that include the bearings and wheel clutch
installed. Order part # 19085 for left wheel kit and part # 19086 for right wheel kit.
*** Wheel clutch must be installed in the correct orientation in order to operate
properly. Wheel clutch is installed correctly when wheels spin freely while
trimmer is moving forward without the engine running (wheels will have resistance
when trimmer is moving backward). One of the wheel bearings may need to be
removed prior to installing the wheel clutch. The wheel clutch has an arrow on the
side to indicate the "free-wheel" direction. Ensure clutch is orientated so the free-
wheel direction corresponds to direction the wheel will rotate while trimmer is
moving forward and press the clutch into the center of the wheel (interference fit).
Then replace the wheel bearing and install the wheel on the axle.
Important!
Rotate wheel in free-wheel direction while mounting on axle
(spin and push at the same time). Ensure both wheel bearings remain fully
seated in wheel during wheel installation and operation. Failure to do so may
cause damage to wheel clutch.
12
Arrow on clutch
shows direction
wheel spins freely
when installed.

Publicidad

Tabla de contenido
loading

Tabla de contenido