Instructions For Use; Humidity-Temperature Meter - Sagola 15020001 Manual De Instrucciones, Lista De Repuestos

4.1. Humidity - Temperature meter
lt is an ideal Humidity & Temperature Meter lnstrument with
seores of practical applications far laboratorial, industrial,
Engineer and professional use.
4.1.1. Features
Display: Large 4-1/2 dual digital LCD display with backlight.
Sensor Type: A single chip relative humidíty and tempera-
ture. Multi sensor module comprising a calibrated. Digital
output.
Response Time: %RH: 10S (90% at +25ºC still air)
Accuracy Note: Accuracy is specified for the following
ambient temperature range: 64 to 82ºF (18 to 28ºC)
Sampling Rate: 2.5 samples per second.
Polarity: Automatic, (-) negative polarity indication.
Over-range: "OL" mark indication.
Low Battery lndication: The "
battery voltage drops below the operating level.
Operating Conditions: 0 to 40°C (32 to 104°F); < 80% RH
non-condensing.
Storage Conditions: -10 to 60°C (14 to 140°F); <80% AH
non-condensing.
Auto Power Off: Meter automatically shuts down atter
approx.15 minutes of inactivity (Sleep Mode).
To override Auto Power Off function (Non-Sleep Mode):
Firstly press hold/backlight button, then press power
button. After the tull display appears, release both buttons.
Lean " " will not shown on the LCD. The unit will not
auto power off now.
Power: One standard 9V, NEDA 1604 or 6F22 battery.
Dimensions / Weight: 225 x 45 x 34 mm. / 200g.
Humidity / Temperature Measurement Range:
Humidity: 0%-100%RH
Temperature: -30 °C- 100 °C, -22ºF- 212 ºF
Resolution: 0.01% RH, 0.01°C/°F.
Humidity Accuracy:
± 2% RH (at 25 °C, 20% - 80% RH).
± 2.5% RH (at other ranges)
NOTE:
The measuring range is from 0% to 100%, but above 80%
and be!ow 20% the deviation is not specified.
Air Temperature Accuracy:
± 0.5 °C / ± 0.9 °F (at 25 ° C)
± 0.8 °C / ± 1.5 °F (all other ranges)

4. INSTRUCTIONS FOR USE

" is displayed when the
- +
4.1.2. Components
1
2
3
5
1 - Humidity / Air Temperature Probe: Humidity & and
Temperature Semiconductor Sensor inside.
2 - LCD Display: 4 - 1/2 dual digits LCD display with units
of ºC, ºF, %RH dew point, wet bulb and low battery "BAT"
MIN /MAX HOLD indication.
3 - MAX/MIN Button: Press MAX/MIN button to enter
MAX, MIN Recording mode (manual range only). Select
the proper range before se!ecting MAX MIN to ensure that
the MAX/MIN reading wili not exceed the testing range.
Press once to select MIN. Press again to select MAX.
Press and hold the Button for over 2 second to tum off
MAX, MIN Recording.
4 - ºF,°C, Dew Point, Wbt Select Button: Press ºF, ºC,
Dew Point. Wbt select Button to enter select ºF, ºC, Dew
Point or Wet Bulb Measurement.
5 - Power ON/OFF Button: Turn the meter power
ON/OFF.
6 - HOLD/Backlight Button: Press HOLD/backlight
Button to enter hold function. The reading will be held when
Data Hold button is pressed.
Press HOLD/backlight Button for over 2 seconds to turn on
or off backlight function.
7 - Battery Compartment.
- 12 -
4
6
7