Assembly & Set-Up - MTD CSV 020 Manual Del Operador

Assembly & Set-Up
Contents of Carton
• Chipper/Shredder Vacuum (1)
• Upper and Lower Handle (1)
• Bottle of Oil (1)
Assembly
NOTE:
This unit is shipped without gasoline or oil in
the engine. Fill up gasoline and oil as instructed in
the accompanying engine manual BEFORE operating
your chipper shredder vacuum.
Handle
1. Remove the hairpin clips (a) from the handle
brackets. Remove the carriage screws (b) and
wing nuts (c) from the lower handle.
a. Place the bottom holes in lower
handle over the pins on the handle
brackets with notch in handle pointing
downwards and secure with
hairpin clips (a). See Figure 3-1.
(b)
(c)
(a)
Figure 3-1
b. Insert carriage screws (b) through
upper hole in lower handle from the
inside and secure with
wing nuts (c). See Figure 3-1.
2. Unfold the upper handle until it aligns with
lower handle. See Figure 3-2. Make sure the
rope guide is on the right side of upper handle.
A
(a)
B
Figure 3-2
3. Secure the two handles by tightening the
star knobs (a). Carriage bolts must be seated
properly into the handle. See Figure 3-2.
• Operator's Manual (1)
• Bag (1)
4. Loosen the wing nut (a) that secures the rope
guide to the right side of upper handle.
a. Slowly pull starter rope out of engine.
b. Slip the starter rope into the rope
guide.
c. Tighten the wing nut (a). See Figure
3-3.
(a)
B
Bag
1. Grasp bag handle with one hand and slide
locking rod on mounting bracket with other
hand toward engine. Use the end of mounting
bracket as leverage when sliding the locking
rod. See Figure 3-4.
1
(a)
B
2. Slip bag over the rim of the discharge opening
and release locking rod to secure bag in place.
3. Snap bag clip to the top of the lower handle.
4. Place the lower bag straps over the top of
lower handle, hooking them on the studs. See
Figure 3-4.
NOTE:
The bag/chute switch button
attached to the mounting bracket must be
fully depressed by the tip of front tab on bag
handle when securing the bag or engine will
not start.
(a)
C
A
Figure 3-3
3
2
4
Figure 3-4
• Engine Operator's Manual (1)
• Safety Glasses (1)
Adjusting Nozzle Height
The nozzle can be adjusted to any six positions,
ranging from 5/8" to 4 1/8" ground clearance. The
nozzle height has to be adjusted according to
chipper shredder conditions.
1. Depress nozzle height adjustment lever
towards wheel. See Figure 3-5.
2
3
1
Figure 3-5
2. Move the height adjustment lever forward
or backward to adjust the nozzle upwards or
downwards. Make sure both levers are in the
same position.
3. Release lever towards deck. See Figure 3-5.
NOTE:
In general, raise the nozzle height
to vacuum a thick layer of leaves. Lower the
nozzle height for smoother surfaces.
Set-Up
Gas and Oil Fill-Up
Refer to the separate engine owner's manual for
additional engine information.
1. Add oil provided before starting unit for the
first time out of the box.
2. Service the engine with gasoline as instructed
in the Engine manual.
WARNING:
Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel the machine indoors or while
the engine is hot or running. Extinguish
cigarettes, cigars, pipes and other sources
of ignition.
WARNING:
Never fill fuel tank indoors
with engine running or until the engine
has been allowed to cool for at least two
minutes after running.
3
5