Descargar Imprimir esta página
Eaton HALO FE0650LPC Instrucciones

Eaton HALO FE0650LPC Instrucciones

Publicidad

Enlaces rápidos

FE0650LPC
FE0650LPCH
(Bronze/Bronze/Bronce)
FE0650LPCW
FE0650LPCWH
(White/Blanc/Blanco)
ENGLISH
IITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Weatherproof silicone caulk
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Fixture designed for wall mount to a recessed junction box only. Install fixture to
junction box marked for use in wet locations.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation. Under Part 15 of the FCC Rules, any changes or modifications to
the fixture described in this instruction sheet that are not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install patio light 7-10 feet above the ground.
• Do not mount fixture close to reflective surfaces such as windows, white walls, white
surfaces and water.
• When installing two fixtures on one switch, make sure the switch is rated for at least
a 1 A inductive load.
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com
PACKAGING CONTENTS / CONTENU DE L'EMBALLAGE/ CONTENIDO DEL PAQUETE
A. Light fixture
B. Mounting bracket
Appareil d'éclairage
Support de montage
Accesorio
Soporte de montaje
E. (3) Wire nuts
(3) Capuchons de connexion
(3) Conectores
de cable
Instruction Manual / Manuel d'instructions/ Instrucciones
C. (2) #6 and (2) #8 junction box screws
(use the size that fits your junction box)
(2) Vis nº 6 et 2 vis nº 8 pour boîtier de
jonction (choisissez la dimension convenant
à votre boîtier de jonction)
(2) Tornillos #6 y (2) tornillos #8 para
montaje de la caja de conexión
(utilice el tamaño que mejor se
adecue a su caja de conexión)
MOUNTING YOUR FIXTURE
NOTE: Do not mount within 2 feet of a highly reflective
exterior inside corner (Fig. 1).
1. Turn off the power at the main fuse/breaker box.
2. Attach mounting bracket (B) to junction box with
two screws (C) provided (Fig. 2).
3. Screw the threaded mounting rod (D) into the center of
the mounting bracket (B) until the threads are
showing on the back side of the mounting
bracket (B) (Fig. 3.)
WIRING YOUR FIXTURE
1. Turn off the power at the main fuse/breaker box.
2. Connect the black fixture wire to the black supply
wire (hot) using wire connector (E) (Fig. 4).
3. Connect the white fixture wire to the white supply
wire (neutral) using wire connector (E) (Fig. 4).
4. Connect the copper ground fixture wire to an
appropriate supply ground or a grounded
junction box.
NOTE: Be careful to connect the wires correctly.
Make sure no bare strands of wire extend from the
wire connector (E) provided or other approved wire
connectors (not provided).
5. Attach fixture to the threaded mounting rod (D).
6. Secure with cap nut (F) (Fig. 5).
7. Add silicone caulk around fixture to help maintain a
weather-resistant seal.
1
D. Threaded mounting rod
Tige de fixation filetée
Varilla roscada para
montaje
F. Cap nut
Écrou borgne
Tuerca tapa
1
2 ft.
2 ft.
2 ft.
2
Junction box
C
C
B
3
Junction box
B
D
4
Junction box
A
D
E
E
5
Junction box
A
D
F

Publicidad

loading

Resumen de contenidos para Eaton HALO FE0650LPC

  • Página 1 Instruction Manual / Manuel d’instructions/ Instrucciones Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com PACKAGING CONTENTS / CONTENU DE L’EMBALLAGE/ CONTENIDO DEL PAQUETE A. Light fixture B. Mounting bracket C. (2) #6 and (2) #8 junction box screws D. Threaded mounting rod (use the size that fits your junction box) Tige de fixation filetée...
  • Página 2 WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. les interférences reçues, même celles qui pourraient provoquer un fonctionnement Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton indésirable. Conformément à la section 15 des règlements de la FCC, toute products will be free from defects in materials and workmanship.
  • Página 3 (E) fournis ou d’autres capuchons de Pour faire une réclamation au titre de la garantie, veuillez appeler Eaton, au 1 800 334 6871, Boîte de jonction connexion approuvés (non fournis). en choisissant l’option 2 pour le Service à la clientèle, ou envoyer un courriel à Consumer- Products@eaton.com et fournir les renseignements ci-après :...
  • Página 4 DIAGNOSTICO Y SOLUCION DE PROBLEMAS La reproducción de este documento sin la aprobación previa por escrito de Eaton está estrictamente prohibida. Para solicitar Problema Causa Posible Acción Correctiva...

Este manual también es adecuado para:

Halo fe0650lpchHalo fe0650lpcwHalo fe0650lpcwh