Publicidad
Enlaces rápidos
Manual
Manuale / Manuel / Betriebsanleitung / Manual / Navodila / Priručnik / Uputstvo / Használati utasítás / Instrukcja
ZNO2055700 A
FlexiTech Safety Uniform Lighting
Small AT Telecommand
231 mm
1
a
0 V
c
Drill in the honeycomb zones (IP43) or in the flexible material parts (IP66).
!
For honeycombs, be careful to battery location.
For corner fixing, use 4 screws.
04/2021
34 mm
b
In order to ensure proper aging of the product, use one of the framed cable entries.
Break a cable entry by
using a screwdriver.
1
Maintained
Non Maintained
+ 45°C
+ 45°C
0°C
+ 5°C
SATI
x 2
2,5 mm
PZ0
C
2
D
A
B
Before use
24h
x2
Ø 5 mm
Rigid or flexible wire
6 mm < Ø < 13,5 mm
Publicidad
Manuales relacionados para Eaton FlexiTech FT1SU250ATT13
Resumen de contenidos para Eaton FlexiTech FT1SU250ATT13
- Página 1 Manual Manuale / Manuel / Betriebsanleitung / Manual / Navodila / Priručnik / Uputstvo / Használati utasítás / Instrukcja ZNO2055700 A 04/2021 FlexiTech Safety Uniform Lighting Small AT Telecommand Maintained Non Maintained + 45°C + 45°C 0°C + 5°C SATI Before use 2,5 mm Ø...
- Página 2 IP66 IK07 SÉCU RITÉ COOP ER Li 3.2V 1.5A 63204 RIOM Installationsdatum Made in Roman T/ M/ Data installazione Even DurationTest Day D Duration Test Day postponed by 7 days FLEXITECH SMALL SAFETY UNI. AT MNM ZNO2055700 A 04/2021 www.eaton.com...
- Página 3 Disconnect the battery, wait for 10 seconds, and reconnect it if you decide to change Even/Odd configuration. See TLU 2 user manual for duration test configuration. CLICK x6 230 V FLEXITECH SMALL SAFETY UNI. AT MNM ZNO2055700 A 04/2021 www.eaton.com...
- Página 4 WEEE: Contact your local dealer EMEA Headquarters Eaton.com/recycling Route de la Longeraie 7 ZNO2055700 A- 04/2021 1110 Morges, Switzerland Eaton.eu Eaton is a registered trademark. 100 % © 2021 Eaton All trademarks are property All Rights Reserved of their respective owners.
- Página 5 Non maintained Use screwdriver to Drill in the honeycomb Maintained Maintained Break a cable entry by place and remove zones or in the f lexible Check the tempera- Before using a screwdriver. material. wire. ture range on the 1st For corner fixing, use 4 maintained Rigid or flexible wire No screwdriver requi-...
- Página 6 Disconnect the battery, wait for Even/ Odd Autotest LED Description 10 seconds, and reconnect it if - Duration Test Day D - Charge / Lamp / Battery - Green / Yellow Installation date - Duration Test Day Battery you decide to change - Constant / Blinking postponed by 7 days - 1wk / 10wks...
- Página 7 Replaceable Disconnect the battery, wait for 10 seconds, and Not replaceable reconnect it if you decide to change Even/Odd Battery pack, Order code If the battery duration is insufficient, replace the configuration. battery. See TLU 2 user manual for duration test confi- When the life time of light source is over, replace the guration.