Eaton HALO FTR1740L Instrucciones

FTR1740L
FTR1740LH
(Bronze/Bronze/
Bronce)
FTR1740LW
FTR1740LWH
(White/Blanc/Blanco)
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Fixture designed for wall or eave mount to a junction box only. Mount fixture to a
grounded, recessed-mounted standard junction box marked for use in wet locations.
• Do not mount below 5 feet.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user's authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
Questions?/Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@eaton.com
PACKAGING CONTENTS/ CONTENU DE L'EMBALLAGE/CONTENIDO DEL PAQUETE
A. Light fixture B. Mounting bracket
Appareil d'éclairage Support de montage
Accesorio Soporte de montaje
E. Support hook
Gancho de soporte
Crochet
Instruction Manual / Manuel d'instructions/ Instrucciones
C. Gasket
Joint
Junta
F. (2) #8-32 x 1-1/4 in. cover
mounting screws (pre-attached)
(2) vis de protection nº 8
de 32 x 1-1/4 po (preenganchado)
(2) Tornillos #8-32 x 1-1/4 pulg.
de montaje de la cubierta (préfixé)
FOR BEST RESULTS
• Install light 10-15 feet above the ground.
• When installing two fixtures on one switch,
make sure the switch is rated for at least a
1 A inductive load.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE: Fixture can be wall or eave mounted (Fig. 1).
NOTE: Coverplate mounts to recessed mounted
standard junction boxes (Fig.2). Junction box must be
at least 1-1/2 inch in depth for proper installation for
recessed mount application.
1. Line up the holes on the mounting bracket (B) with
the holes on your junction box. Using either (2) #6
screws or (2) #8 screws (D) (depending on size of
the holes in your junction box), attach the mounting
bracket (B) to your junction box (Fig. 3).
2. Thread fixture wires through coverplate gasket (C)
(Fig. 3).
3. Hang one end of the support hook onto the mounting
bracket and hang the light fixture on the other end of
the support hook (Fig. 4).
4. Connect fixture black wire to house black wire and
fixture white wire to house white wire by firmly
pushing into quick connect wiring connectors
(Fig. 5).
5. Connect house ground wire and fixture ground wire
by firmly pushing into quick connect wiring
connector. (Fig. 5). Attach fixture (A) to the mounting
1
D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pou
boîtier de jonction (choisissez la dimension convenant
à votre boîtier de jonction)
(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4
pulg. para montaje de la caja de conexiónes (utilice el
tamaño que mejor se adecue a su caja de conexiónes)
G. (2) Decorative screw cover caps
(2) cache-vis décoratifs
(2) Cubiertas tapatornillos decorativas
1
2
1-1/2 in.
3
D
D
Wall mount
Eave mount
1-1/2 in.
Round Octagonal
B