Conference - Midland BT Next Manual Del Usuario

Conference

The "Conference" mode allows the communication with four people simulta-
neously. The BT Next C. Conference unit can work as usually, with "one to one"
communication up to 6 people (standard Intercom mode) or with 4 people confe-
rence intercom (Conference mode).
How to use the conference mode
First of all you need to pair all the units in a "chain" mode, second the "Conference"
feature must be active on all the units paired.
Pairing
To use the conference mode you need to pair all the units in a "chain" configura-
tion. The BWD button of the first unit must be paired to the FWD button of the
second unit. The BWD button of the second unit must be paired to the FWD button
of the third unit and so on, till the fourth!
1 2
The first and the last unit must not be paired together (the chain must stay open).
The unit number 1 can talk to the last unit (number 4) only "through" the unit
number 2 and number 3. That means to have the conference with four people, all
the unit must have the intercom open.
Activate the conference mode
Just after you finish to pair the units as a "chain", you need to activate the confe-
rence mode in all the unit.
Conference mode on:
Keep pressed the FWD button for 7 sec. When in Intercom mode the voice an-
nouncement "Conference" will tell you that it is active.
Conference mode off:
Keep pressed the FWD button for 7 sec. When in Intercom mode the voice an-
nouncement "Intercom" will tell you that you are back to the standard Intercom
functionality.
When the Conference mode is active, only two mode are available:
Conference (that replace the Intercom mode) and FM radio.
There is no more the "Phone" mode because all the devices paired on Vol+ and Vol
24 - Midland BT Next
3 4
– are temporary disconnected to guarantee the stability of the conference mode.
Attention: when the "conference" mode is active, the "Talk2All- Universal Intercom"
(to talk with not Midland brand intercom) is not available.
Also if one unit was paired on the CTRL (middle) button, it is temporary unavaila-
ble, you need to disable the "Conference" mode and go back to the standard "one
to one" Intercom mode.
How to use the conference mode
When the conference mode is active, is possible to open the intercom communi-
cation pressing both the FWD and BWD button. One click on the button will open
the intercom communication, one click on the same button will close it.
The two units that are in the middle of the chain (unit 2 and 3) must keep the
intercom open on both FWD and BWD button to allow the full communication of
the four units together.
Disable the "conference" mode
The conference mode can be disable in every moment, just pressing the FWD
button for 7 sec. You will hear the voice announcement "Intercom" and from that
moment your BT Next C. Conference will start working with "one to one" intercom
and all the devices paired on Vol+ and Vol- are back, together with the "Phone"
mode and the "Talk2All-Universal intercom" feature.
"One Click Talk" function
When the conference mode is active, is possible to open the intercom communi-
cation to all the 4 users just in "one click". Press short the CTRL (middle) button and
you will automatically open the conference intercom to all the unit connected.
Talk 2 All - Pairing to a different brand intercom.
Thanks to the "Talk2 All - Universal Intercom" feature it is now possible to
pair your BT Next C. to a different brand intercom available on the market.
You can pair a maximum of two not Midland Intercom, one on the
"Forward" button and one on the "Backward" button.
•
On the BT Next C. enter the setup mode: (with the unit OFF press
and hold down
the Middle button about 7 sec. until the Red light is on permanen-
tly).
•
Keep pressed the "Forward" button or the "Backward" button for
7 seconds: the Red and Blu LED light will start flashing fast, than
(while you still keep the button pressed) the Red and Blu LED light
will change to slow flashing. Now you can stop pressing the button.