Publicidad

Enlaces rápidos

DECLARATION OF CONFORMITY
This product is marked
– Low voltage no. 73/23 EEC and 93/68 EEC.
– Electromagnetic compatibility no. 89/336 ECC, 92/31 EEC
and 93/68 EEC.
This declaration will become void in case of misuse and/or non
observance though partial of manufacturer's installation and/or
operating instructions.
COOLING ONLY MODELS
OPERATING LIMITS
Maximum conditions
Outdoor temperature : 43°C D.B.
Room temperature
: 32°C D.B. / 23°C W.B.
Minimum conditions
Outdoor temperature : 19°C D.B.*
Room temperature
: 19°C D.B. / 14°C W.B.
Model name GRVXXXL5
* : –15°C D.B.
HEAT PUMP MODELS
OPERATING LIMITS
Cooling Maximum conditions
Outdoor temperature : 43°C D.B.
Room temperature
: 32°C D.B. / 23°C W.B.
Cooling Minimum conditions
Outdoor temperature : 19°C D.B.
Room temperature
: 19°C D.B. / 14°C W.B.
Heating Maximum conditions
Outdoor temperature : 24°C D.B. / 18°C W.B.
Room temperature
: 27°C D.B.
Heating Minimum conditions
Outdoor temperature : –8°C D.B. / –9°C W.B.
ACCESSORIES SUPPLIED WITH THE UNIT
PARTS
FIGURE
Q.TY
RAWL PLUG
TAPPING
SCREW
REMOTE
CONTROL UNIT
AAA ALKALINE
BATTERY
*
Available only for heat pump models R22.
09/2001
as it satisfies Directives:
PARTS
FIGURE
DRAIN
7
*
ELBOW
AIR CLEAN
7
FILTER
1
2
INSTALLATION INSTRUCTIONS
- Compact wall-mounted split units
Model Combinations
Combine indoor and outdoor units only as listed below.
COOLING ONLY MODELS R22
Indoor Units
MCAV77C5VA*
MCAV97C5VA*
MCAV127C5VA*
Indoor Units
MCAV77R5VA*
MCAV97R5VA*
MCA127R5TA*
COOLING ONLY MODELS R407C
Indoor Units
MCAV77C5VA*
MCAV97C5VA*
MCAV127C5VA*
Indoor Units
MCAV77R5VA*
MCAV97R5VA*
MCAV127R5VA*
R407C MODELS: for the other installation works of GRV models refer
to the "Installation Instructions" (green pages) on the top of the outdoor
unit.
Power Supply:
220 - 240 V ~ 50 Hz
Q.TY
Tools required for installation (not supplied)
1. Standard screwdriver
1
2. Phillips head screwdriver
3. Knife or wire stripper
2
4. Tape measure
5. Level
6. Sabre saw or key hole saw
7. Hacksaw
8. Core bits ø 5
37.4163.181.0
CSMC-C / CSMC-R -
Outdoor Units
GR79C5TB*
GR99C5TB*
GR129C5TB*
HEAT PUMP MODEL R22
Outdoor Units
GR79R5TB*
GR99R5TB*
GR129R5TB*
Outdoor Units
GRV71L5VA*
GRV91L5VA*
GRV121L5VA*
HEAT PUMP MODEL R407C
Outdoor Units
GRV79R5VA*
GRV99R5VA*
GRV129R5VA*
19. Hammer
10. Drill
11. Tube cutter
12. Tube flaring tool
13. Torque wrench
14. Adjustable wrench
15. Reamer (for reburring)
16. Hex. key
10 11 302 F.GB.I.E.D.05
EG
I
F
D
E

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Technibel CSMC-C Serie

  • Página 1 INSTALLATION INSTRUCTIONS - Compact wall-mounted split units CSMC-C / CSMC-R - Model Combinations DECLARATION OF CONFORMITY Combine indoor and outdoor units only as listed below. This product is marked as it satisfies Directives: – Low voltage no. 73/23 EEC and 93/68 EEC. COOLING ONLY MODELS R22 –...
  • Página 2 IMPORTANT! • Ground the unit following local electrical codes. • The Yellow/Green wire cannot be used for any connection Please read before installation different from the ground connection. • Connect all wiring tightly. Loose wiring may cause overheating This air conditioning system meets strict safety and operating at connection points and a possible fire hazard.
  • Página 3: Electrical Data

    Installation site selection - Indoor unit • Select a sufficiently strong location to support the weight of the AVOID unit. • Direct sunlight. • Select a location where tubing and drain hose have the shortest • Nearby heat sources that may affect unit performance. run to the outside.
  • Página 4: Istruzioni Di Installazione

    ISTRUZIONI DI INSTALLAZIONE - Condizionatori d’aria Split System a parete CSMC-C / CSMC-R - Combinazione modelli DICHIARAZIONE DI CONFORMITÀ Combinare Unità Interna ed Esterna solo come elencato qui sotto. Questo prodotto è marcato in quanto conforme alle Direttive: – Bassa Tensione n. 73/23 CEE e 93/68 CEE. MODELLI SOLO FREDDO R22 –...
  • Página 5 IMPORTANTE! • Eseguire la messa a terra dell’unità secondo le norme elettriche locali. Leggere prima di iniziare l’installazione • Il conduttore giallo/verde non può essere utilizzato per collegamenti diversi dalla messa a terra. Questo sistema di condizionamento deve seguire rigidi standard •...
  • Página 6: Dati Elettrici

    Scelta del luogo di installazione unità interna • Verificare che il piano di appoggio sia sufficientemente resistente da EVITARE sostenere il peso dell’unità. • L’esposizione diretta al sole. • Scegliere una posizione in modo che la distanza tra le due unità sia •...
  • Página 7 NOTICE D’INSTALLATION NOTICE D’INSTALLATION - Climatiseurs split muraux compacts CSMC-C / CSMC-R - Combinaison de modèles DECLARATION DE CONFORMITE N’associez les appareils intérieurs et exterieurs que de la Ce produit est marqué puisque il est conforme aux manière indiquée ci-dessous. Directives: –...
  • Página 8 IMPORTANT! • Effectuez la mise à la terre de l'appareil en respectant les réglementations électriques locales. Veuillez lire ce qui suit avant de commencer • Le câble jaune/vert ne peut en aucun cas être utilisé pour toute Ce système de conditionnement de l'air répond à des normes autre connexion que celle de la mise à...
  • Página 9 Choix de l'emplacement d'installation - Appareil intérieur RECHERCHEZ • Un emplacement approprié à partir duquel l'ensemble de la pièce peut être EVITEZ climatisé de manière uniforme. • L'exposition directe au soleil. • Un emplacement suffisamment solide pour supporter le poids de l'appareil. •...
  • Página 10: Mitgeliefertes Zubehör

    INSTALLATIONSANLEITUNGEN - Kompakte Split-Wandgeräte CSMC-C / CSMC-R - Modellkombinationen KONFORMITÄTSERKLÄRUNG Innenraum- und Außengeräte sollen nur wie in der folgenden Liste miteinander verbunden werden. Dieses Produkt ist mit -Zeichen gekennzeichnet, weil es den folgenden Richtlinien entspricht: NUR KÜHLUNG MODELLE R22 – Niederspannungsrichtilinie 73/23 EWG und 93/68 EWG. Innenraumgeräte Außengeräte –...
  • Página 11 WICHTIG! Verbindungen unzureichende Erdung können Bitte vor Arbeitsbeginn lesen Unfallverletzungen oder Tod verursachen. • Erden Sie das Gerät gemäß den örtlich zutreffenden Vorschriften. Diese Klimaanlage entspricht strengen Sicherheits- und • Das Gelbe/Grüne Kabel ist für die ausschließliche Verwendung Betriebsnormen. als Erdleitung. Für den Installateur oder Bediener dieser Anlage ist es wichtig, sie •...
  • Página 12: Elektrische Angaben

    Wahl des Installationsortes - Innenraumgerät • Wählen Sie eine Stelle, an der der Boden das Gewicht des Gerätes tragen VERMEIDEN SIE kann. • Direkte Sonneneinstrahlung. • Wählen Sie eine Stelle, von der aus die Rohre und der • Wärmequellen in der Nähe des Gerätes, die dessen Leistungsfähigkeit Wasserablaufschlauch den kürzesten Weg nach darußen haben.
  • Página 13: Material Suministrado

    INSTRUCCIONES DE INSTALACION - Split murales compactos CSMC-C / CSMC-R - Combinación de Modelos DECLARACION DE CONFORMIDAD Combinar la unidad interior y la exterior como se indica en Este Producto está marcado porque responde a las la siguiente lista. Directivas: –...
  • Página 14 ¡IMPORTANTE! • Realizar la puesta a tierra de la unidad siguiendo las normas eléctricas locales. Leer antes de empezar la instalación • El conductor amarillo/verde no se puede utilizar para conexiones que no sean la de tierra. Este sistema de acondicionamiento cumple medidas rígidas de •...
  • Página 15: Material Adicional Para La Instalacion (No Suministrado)

    Dónde instalar la unidad interior • Controlar que el lugar de apoyo es lo suficientemente resistente como EVITAR para soportar el peso de la unidad. • La exposición directa al sol. • Elegir una posición de modo que la distancia entre las dos unidades •...
  • Página 16 INDOOR UNIT • UNITÀ INTERNA • UNITE INTERIEURE • INNENEINHEIT • UNIDAD INTERIOR Minimum operation and maintenance area. Area minima di esercizio e manutenzione. Surface minimum de fonctionnement et d’entretien. Raumbedarf des Gerätes. Area mínima de funcionamiento y manutención. 2000 Área mínima para o funcionamento e manutenção.
  • Página 17 Tubing connections from the rear. Use the rear panel as a template. Check the horizontal position with the level. Mark the holes to be made. Collegamento tubi posteriore. Utilizzare il pannello posteriore come dima, mettere a livello, evidenziare i fori da eseguire. Sortie arrière des tubes.
  • Página 18 Use the screws to fix the rear panel to the wall. Make sure the panel is flush against the wall. Any space between the wall and unit will cause noise and vibration. Usando le viti, fissare il pannello posteriore al muro. Assicurarsi che l’unità...
  • Página 19 To fix the front panel again, insert it in the lower side of the unit and align it with the blocking points. Then push lightly on the shown marks. Per rimontare il pannello frontale inserirlo nella parte bassa dell’unità, allinearlo sui punti di bloccaggio, applicare una leggera pressione sui punti indicati.
  • Página 20: Salida Posterior Derecha De Los Tubos

    Running power wires plus ground wire from indoor to outdoor unit (see tab. for size of wires). Stendere un cavo multipolare con filo di terra tra le due unità (vedere tabella per la sezione dei fili). Passer les fils électriques et un fil de terre, entre les deux unités (voir tableau pour la section des fils).
  • Página 21 LEFT REAR TUBING Insert the tubes connecting the units from the outside, then bend them right and remove the inferior removable part of the frame. Hang up the unit and extend the support on the back of indoor unit to make the connection easier. USCITA TUBAZIONI LATO SINISTRO POSTERIORE Inserire le tubazioni di collegamento dall’esterno, quindi piegarle verso destra, rimuovere la parte inferiore amovibile della struttura.
  • Página 22 Die Leitungen für die Klemmbrett-Verbindung vorbereiten und sie verbinden. (Sieh elektrische Angaben). WARNUNG Stellen Sie sich sicher, daß alle Kabelverbindungen fest sind. Lose Kabel können zur Überhitzung des Anschlüsses oder Fehlfunktion des Gerätes führen. Feuergefahr mag ebenfalls bestehen. Preparar los hilos eléctricos para la conexión con la regleta de bornes y conectarlos (Véase el esquema para la conexión).
  • Página 23 Fill the tube and verify that the condensate can flow correctly. Reassemble the grille according to “L”. Riempire la tubazione quindi verificare il corretto scarico della condensa e rimontare la griglia come al punto L. Remplir le bac et vérifier que la sortie des condensats soit correcte. Remonter la grille selon “L”.
  • Página 24 OUTDOOR UNIT • UNITÀ ESTERNA • UNITE EXTERIEUR • AUßENEINHEIT • UNIDAD EXTERIOR Minimum operation and maintenance area Area minima di esercizio e manutenzione. Surface minimum de fonctionnement d’entretien. Raumbedarf des Gerätes. Area mínima de funcionamiento y manutención. Provide a solid base for outdoor unit raised from the ground level. Fix unit to base using 4 anchor bolts.
  • Página 25 Use insulated copper tube. Cut approximate 30-50 cm. longer than actual distance between units. min. 8 mm min. 8 mm Utilizzare del tubo in rame isolato. Tagliare con lunghezza maggiorata di 30-50 cm oltre la distanza tra le unità. Utiliser de tube en cuivre isolé. Couper à une longueur de 30-50 cm en plus de la distance entre les unités.
  • Página 26 Lubricate Eine gute Kelchung sollte die folgenden Eigenschaften besitzen: - die Oberfläche der Innenseite ist glänzt und glatt - die Kante ist glatt - die Kelchförmig zulaufenden Seiten sind von gleicher Länge. Die Oberfläche, die miteinander in Berührung kommen, mit Frostschutzmittel- Schmierfett schmieren und dann zuschrauben.
  • Página 27 Remove caps from service valves of both tubes. Then start vacuum pump and let it run for the time indicated in the table (vacuum 10 mm Hg abs.). Rimuovere i cappucci delle valvole di entrambi i tubi. Quindi avviare la pompa High pressure del vuoto per un tempo consigliato come da tabella (vuoto di 10 mm Hg assoluti).
  • Página 28 Turn the service valves stem in counterclockwise to fully open the valves. At this point vacuum pump flexible hose can be disconnected. Replace bonnet and flare nut, tighten them to 200 kg/cm with a torque wrench. Aprire completamente le valvole di servizio (senso antiorario). A questo punto scollegare il flessibile della pompa del vuoto.
  • Página 29 The service port on the wide tube service valve uses a Schrader core valve to access the refrigerant system. Therefore, be sure to use a hose connector which has a push-pin inside. La valvola di servizio del rubinetto dell'unità esterna da utilizzare per il vuoto del sistema, il ripristino carica refrigerante e la misurazione della pressione di esercizio è...
  • Página 30 SYSTEM WIRING DIAGRAM • COLLEGAMENTI ELETTRICI DEL SISTEMA • BRANCHEMENTS ELECTRIQUES DU SYSTEME • ELEKTRISCHE ANSCHLÜSSE DES SYSTEMS • CONEXIONES ELECTRICAS DEL SISTEMA COOLING ONLY MODELS INDOOR OUTDOOR UNIT UNIT MODELLI SOLO FREDDO MODELES FROID SEUL NUR KÜHLUNG MODELLE MODELOS SOLO REFRIGERACION POWER SUPPLY 220-240V ~ 50Hz HEAT PUMP MODELS...
  • Página 31 Supply power wire A: Multipolar electric wire. Size and length of the suggested electric wire are showed on table “electrical data”. The wire must be Mod. H05VV-F (according to CEI 20-19 CENELEC HD 22). Make sure the length of the conductors between the fixing point and the terminals allows the straining of the conductors L, N before that of the grounding.
  • Página 32 Cable de alimentación A: Cable eléctrico multipolar; la sección y la longitud del cable eléctrico aconsejado están indicadas dentro de la tabla “Datos eléctricos”. El cable debe ser del tipo H05VV-F (según CEI 20-19 CENELEC HD22). Asegurarse de que la longitud de los conductores entre el punto de fijación del cable y el tablero de bornes es tal que los conductores activos se tiendan antes del conductor de puesta a tierra.
  • Página 33 TEST RUN • COME ESEGUIRE LA PROVA DEL CONDIZIONATORE (TEST RUN) • CONTROL FINAL ENDKONTROLLE • COMO REALIZAR LA PRUEBA DEL ACONDICIONADOR (TESTRUN) TEST Cooling mode Heating mode Switch on the power supply. Press the ON/OFF button and change Switch on the power supply. Press the ON/OFF button and change to heating mode on the remote control unit then press the ON/OFF to cooling mode on the remote control unit.
  • Página 34 REMOTE CONTROL UNIT INSTALLATION • POSIZIONE DI INSTALLAZIONE TELECOMANDO • EMPLACEMENT DE LA COMMANDE A DISTANCE • POSITION DER FERNBEDIENUNG • POSICION DE INSTALACION DEL MANDO A DISTANCIA REMOTE CONTROL UNIT INSTALLATION The remote control unit may operated either from a non-fixed position or from a wall-mounted position. To ensure that the air conditioner operates correctly, DO NOT install the remote control unit in the following places: •...
  • Página 35 ( 1 ) ( 2 ) WALL-MOUNTED NON-FIXED POSITION (A) • Momentarily place the remote control unit in the desired mounting position. • Verify that the remote control unit can operate from this position. • Fix the support at the wall with two screws and hang the remote control unit. WALL-MOUNTED FIXED POSITION (B) •...
  • Página 36 PUMP DOWN Pump down means collecting all refrigerant gas in the system quand on doit déplacer le climatiseur, et pour les interventions back into the outdoor unit without losing gas. Pump down is de réparation sur le circuit frigorifique. used when the unit is to be moved of before servicing the Das bedeutet: das Kühlmittel in die Außeneinheit ohne Gas- refrigerant circuit.
  • Página 37 PARTICULAR INSTALLATIONS FOR OUTDOOR UNIT (NOT SUPPLIED) • INSTALLAZIONI PARTICOLARI PER UNITÀ ESTERNA (NON FORNITE) • INSTALLATIONS SPECIALES POUR L'APPAREIL EXTERIEUR (NON LIVREES) • BESONDERE INSTALLATIONEN FÜR AUßENEINHEITEN (AUF ANFRAGE) • INSTALACIONES ESPECIALES PARA UNIDAD EXTERIOR (NO SUMINISTRADAS) GRVXXXL Models It is recommended to use baffle plates for models designed for low ambient temperatures when the outdoor unit is installed in a position exposed to strong wind (such as seasonal wind with low air temperature in winter) that could make...
  • Página 38 lectric wiring diagrams’ symbols / Simboli schemi elettici / Symboles des schemas électriques / Symbole der System-Schaltplanen Símbolos de los esquemas eléctricos / Símbolos dos esquemas elétricos SYMBOL CRANK CASE HEATER RISCALDATORE CARTER RESISTANCE DE CARTER-MOTEUR KURBELGEHÄUSEHEIZUNG CALENTADOR DEL CÁRTER COMPRESSOR MOTOR MOTORE COMPRESSORE MOTEUR DE COMPRESSEUR...
  • Página 39 In order to carry on a constant improvement, our products can be modified without prior notice. Per garantire un costante miglioramento dei nostri prodotti, ci riserviamo di modificarli senza preavviso. Par souci d’amélioration constante, nos produits peuvent être modifiés sans préavis. Unsere Produkte werden laufend verbessert und können Vorankündigung abgeändert Werden.

Tabla de contenido