System Sensor M201E Manual De Instrucciones

94 mm
83 mm
1
2
3
4
A B
5
1
6
7
0
8
9
10
8 9 8 9
11
6 7 6 7
10
5 11 5
12
4 4
12
3 3
13
2 2
14
1 1
0 15 0
A x10 B x1 C
1:1 M200E-SMB
Fig./Abb. 2
a
-
+
b
-
c
+
d
+
e
f
+ -
g
h
EOL
Fig./Abb. 3
a
-
b
+
c
-
+
d
+
e
NC
{
C
f
NO
Fig./Abb. 4
0786 DOP-IOD007
07 EN54-17: 2005, EN54-18: 2005
D200-94-01
23 mm
60°C
93
mm
-20°C
1:3 M200E-PMB
1:2 M200E-DIN
Fig./Abb. 1
1
2
3
M201E
4
5
6
7
8
9
10
8 9 8 9
6 7 6 7 6 7
11 10 10
11 11
5 5 5
12
4 4 12 12 4
3 3 3
13 13
2 2 2
14 14
1 1 1
0 0 15 15 0
A x10 B
1
2
3
M201E
4
5
6
7
8
9
10
8 9
11 6 7 6 7
10
11
5 5
12
4 4
12
3 3
13
2 2
14
1 1
0 15
x10
A B
(i)
+
(iii)
Fig./Abb. 5
Pittway Tecnologica S.r.l
Via Caboto 19/3
34147 Trieste, Italy
Pittway Tecnologica S.r.l, Via Caboto 19/3, 34147 Trieste, Italy
M201E
EN
This manual is intended as a quick reference installation guide. Please refer to the
85 g
control panel manufacturers installation manual for detailed system information.
The M200 series of modules are a family of microprocessor controlled interface
M201E +
devices permitting the monitoring and/or control of auxiliary devices. The M201E is
M200E-SMB
an output module that allows the control of auxiliary devices such as fire shutters or
sounders.
A single tri-colour LED indicates the status of the module. In normal conditions, the
LED can be set by command from the control panel to blink green when the module is
230 g
polled. When the control panel switches the relay to the energised state the LED can
be set to continuous green.
SPECIFICATIONS
Operating Voltage Range:
Maximum Standby Current
(µA @24 V and 25
LED Current (Red):
LED Current (Yellow):
Maximum rated continuous current with the
Maximum rated isolator switching current (under short circuit) (I
Maximum leakage current (I
Maximum series impedance with the isolator closed (Z
Humidity:
Maximum Wire Gauge
INSTALLATION
Note: These modules must only be connected to control panels using compatible
proprietary analogue addressable communication protocols for monitoring and control.
M200 series modules can be mounted in several ways (See Figure 1):
1:1 An M200E-SMB custom low profile surface-mounting box. The SMB Base is
affixed to mounting surface, and then the module and cover are screwed onto
the base using the two screws supplied. Box dimensions: 132mm(H) x 137mm(W)
x 40mm(D)
A B
1:2 An M200E-DIN Adaptor allows mounting onto standard 35mm x 7.5mm "Top Hat"
1
DIN rail inside a control panel or other suitable enclosure. Push module into adaptor
bracket until it clips into place. Locate top clip over DIN rail and rotate bottom down
0
to clip into place. To remove, lift up, then rotate top away from the rail.
1:3 An M200E-PMB Panel Mount Bracket allows the module to be mounted directly
8 9
into a panel or other suitable enclosure. Adaptor bracket is mounted directly into
panel using 2 x M4 Pan head screws. Module is pushed into adaptor until it clips
into place.
x1 C
Wiring to all series M200 modules is via plug in type terminals capable of supporting
conductors up to 2.5mm²
Disconnect loop power before installing modules or sensors.
The module address is selected by means of rotary decade address switches (see
Figure 4). A screwdriver should be used to rotate the wheels to select the desired
address, either from the front or the top of the module. (Note: The number of addresses
available will be dependent on panel capability, check the panel documentation for
information on this.)
Short Circuit Isolators
A B
All M200 series modules are provided with short circuit monitoring and isolators on the
1
intelligent loop. If required the isolators may be wired out of the loop to facilitate the
use of the modules on high current loaded loops, for example if sounders are used.
0
To achieve this, the loop out positive should be wired to terminal 5 rather than terminal
2. See the relevant wiring diagram for details.
8 9
M201E WIRING
The M201E can be wired for either Supervised (Figure 2) or Non-Supervised
0
(Figure 3) operation respectively. If using the VdS optional polarised resistor EOL
x1
C
device (part no. M200E-EOL-RD) note that the EOL device red wire connects to
terminal 8 and the orange wire to terminal 9, as monitoring voltages are reversed.
M201E Single Output Module with Supervised Output
(ii)
When the module is used in supervised mode and power is supplied to the module,
a switched negative input on terminal 12 can be used to signal an external fault
condition, such as a power supply fault. Loss of power is also supervised in this mode
such that if the supply voltage falls below 7V a fault indication is achievable. Note that
the use of this fault mode is dependant on panel software. Please contact the panel
manufacturer for further details.
Wire as follows (see Figure 2):
a: T1 Loop Output -. b: T2 Loop Output +. c: T3 Loop Input -. d: T4 Loop Input +
e: T5 Loop Output +. If short circuit isolation is not required, loop output+ should be
wired to terminal 5 and not 2. Terminal 5 is internally connected to terminal 4.
f: To enable output circuit supervision, the link supplied must be fitted across
terminals 6 and 7,and the load must be polarised.
INSTALLATION INSTRUCTIONS
FOR THE M201E OUTPUT MODULE
15 to 30VDC (Min 19.5VDC for LED operation)
310µA - No Communication
C): 510µA - Communication LED blink enabled - 5 secs
o
410µA - Read 16 sec. LED blink 8 sec
2.2mA
8.8mA
isolator
max) with the isolator open (isolated state): 15mA
L
5% to 95% relative humidity (non-condensing)
2.5mm²
CAUTION
CAUTION
Electrostatic Sensitive Device
Observe precautions when handling and making connections
I 56- 2100- 020
closed (I max): 1A
c
max): 1A
s
max): 170 m ohm at 15Vdc
c
I56-2100-020