Orbis NEXU Manual De Uso página 11

For security reasons, always enter a minimum of 8 characters, with at least one number or special
character, one lower-case letter and one upper-case letter.
To confirm the password change, press the CHANGE icon and a notification will confirm that the
password change has been made correctly.
 Cancel Account
When you wish to permanently delete your account, press the "CANCEL ACCOUNT" icon to
access the corresponding page.
ATTENTION:
Cancelling your account eliminates the option to manage the NEXU chronothermostat remotely via
the application.
Enter the email address and password previously registered and confirm with the OK button. A
notification will confirm that your account has been successfully cancelled.
TECHNICAL ASSISTANCE
Select the TECHNICAL ASSISTANCE icon indicated by the question mark to access the section.
You must first give consent to the processing of your details for the purposes of technical
assistance.
If you press this icon, you can contact the ORBIS Technical Assistance service by
telephone to obtain information, support and assistance with the NeXU
chronothermostat/app.
The service is available Monday-Friday, from 7:00 am to 3:30 pm.
Touch this icon to consult these instructions for using the chronothermostat / app
directly.
Touch this icon to send an email directly to the Technical Assistance Service to
obtain information, support and assistance with the NeXU chronothermostat / app.
Touch this icon to send a WhatsApp message directly to the Technical Assistance
Service to obtain information, support and assistance with the NeXU
chronothermostat / app. The service is available Monday-Friday, from 7:00 am to
3:30 pm.
CHRONOTHERMOSTAT MANAGEMENT
The NEXU chronothermostat can be operated in one of the following four operating modes:
 Automatic, according to the program set through the scenario mechanism, via the "ORBIS
NEXU Wi-Fi Chronothermostat" app. The screen displays the
corresponding to the current scenario, for example, for scenarios with 6 periods:
P1 (I get up)  P2 (I leave in the morning)  P3 (I come home for lunch)  P4 (I leave in the
afternoon)  P5 (I come home at night)  P6 (I go to bed)
Or for scenarios with 4 periods:
P1 (I get up)  P2 (I leave in the morning)  P3 (I come home at night)  P4 (I go to bed)
 Temporary manual operation: the symbol
 Permanent manual operation: the symbol
 OFF no operation is carried out and this symbol appears on screen.
Below are the operations that can be carried out directly on the NEXU chronothermostat:
CHRONOTHERMOSTAT ON/OFF
Press the symbol to turn on/off the chronothermostat. When it is turned OFF, the
appears on screen.
Wi-Fi CONNECTION
When the chronothermostat is connected to the home Wi-Fi network, the symbol
above the word Wi-Fi.
DISPLAYING THE TIME / TYPE OF SCENARIO
Press the symbol  to display the CURRENT SCHEDULE, the type of scenario programmed with
either the indication P4 (scenario with 4 periods) or P6 (scenario with 6 periods) and the number of
the day of the week (d01 to indicate Monday, d04 to indicate Thursday, etc.).
To change the time and date (year, month and day), press both symbols / together at the same
time for 5 seconds, until Diff. Set appears on screen. Press the symbol  and the following will
appear sequentially on screen: Year, month, day, hour, minutes and change for daylight savings
time (AUTO: ON – OFF). To change the values, press the symbols / and confirm with .
ATTENTION: The type of scenario programmed cannot be changed from the NEXU
chronothermostat. This operation can only be carried out from a smartphone / tablet, using the
"ORBIS NEXU Wi-Fi Chronothermostat" app.
TEMPORARY MANUAL OPERATION
While the automatic operation is active (according to the set program), it is possible to temporarily
change the expected temperature for the current scenario. The temporary manual operation will
automatically expire the next time the scenario is changed. To activate this mode, press either /
to increase/decrease the temperature value.
The setting always starts from the temperature value programmed for that time. During the
temperature selection, the symbol
disappears a few seconds after the setting is completed. When the temporary manual operation is
active, the symbol blinks on screen. To leave this condition, simply touch the symbol twice
PERMANENT MANUAL OPERATION (THERMOSTAT)
When automatic operation is active (according to the set program), it is possible to change to
THERMOSTAT MODE, without programming the time and with the activation/deactivation of the
system according to the programmed temperature. To activate it, touch the symbol
temperature by pressing / to increase/decrease the temperature value. The setting always
starts with the last temperature value set.
During the temperature selection, the symbol
Temp. This disappears a few seconds after the setting is completed. When the function is active, the
symbol appears on screen. To leave this condition, simply touch the
DIFFERENTIAL VARIATION
To change the differential value (by default, 0.2 °C), press the / symbols at the same time for 5
seconds, until Diff appears on screen. The available values are 0.2-0.4-0.6-0.8 and 1°C. Once the
desired value has been selected, wait a few seconds and the new differential will be stored
automatically.
ANTI-FREEZING TEMPERATURE VARIATION
To change the value of the anti-freezing temperature (by default, +5 °C), press the symbol
10 seconds until the screen displays the word AI. Set the value between 1 °C and 9 °C by pressing
the symbols / to increase/decrease the temperature value. Once the desired value has been
selected, wait a few seconds and the new anti-freezing temperature will be automatically stored.
KEYPAD LOCK
To prevent tampering of the chronothermostat, the keypad can be locked by pressing the symbols
and  together at the same time until the lock symbol appears on screen
keypad does not prevent operations via a smartphone/tablet.
To unlock the keypad, follow the same procedure.
RESET
To return to the original factory settings, press
seconds and until "dEL" appears on screen. All the programs and settings will return to their default
values, except for the "device name".
This operation cancels the Wi-Fi configuration of the chronothermostat, and the signal symbol
disappears above the Wi-Fi word. The chronothermostat icon on the APP does not turn dark.
Bear in mind that since the chronothermostat icon has not moved to the app rubbish bin, the
thermostat is still linked to your account. It is not necessary to repeat the pairing procedure. To
reset the previous Wi-Fi connection or set a new one, proceed as indicated at the start of the "Wi-
Fi CONNECTION" paragraph.
Alternatively, it is possible to restart the NEXU chronothermostat pressing the RESET button with a
pin in the hole to erase all the programmed settings. The hole is located on the bottom of the
device.
This operation makes it possible to resolve any malfunction that occurs in the microprocessor. After
a reset, the screen will show all the segments for a short time and then it will be ready to receive
the new settings.
The Reset operation allows you to reset the program. It will not affect the Wi-Fi, connection.
Pressing the Reset button does not disconnect the thermostat from the existing Wi-Fi network.
icon, along with the number
blinks on screen.
appears unblinking on screen.
blinks on screen, next to the word Set Temp, which
appear on screen, along with the words Set
symbol once.
and  at the same time for approximately 5
icon
appears
.
and set the
for
. Locking the