Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
•
Lay bagger cover upside
- down (leave
protective
covering
intact),.
.
Slide
bagger
handle
insert
(9)
into
depression
on inside
of bagger
cover,.
Make
sure
the
two
tabs
at the
top
lock into place with the bagger
cover.
Teeth
at the
bottom
of the
bagger'
......................
handle
insert should
slide into place in
between
the teeth on the bagger cover,
.
Slide two square
nuts (10) into the two
square
slots at the front of the bagger
cover and two square
nuts into the two
square
slots (one slot on each side) at
.......................... the- rear-, handle
of the- bagger
cove[:
.
Turn
bagger
assembly
(3)
upside
down,
lining
up holes
in the frame
to
holes in the bagger cover, making
sure
frame upper weldment
tubing
is seated
in plastic
cradle
in the bagger
handle
insert (9).
•
Install four 1/4" hex bolts (!1)
in holes
with four square
nuts (10) and tighten
until seated°
•
Install two 1/4" screws
(12) in holes at
center of frame upper weldment.
,
Turn assembly
right-
side up.
°
Install
two
1\4" carriage
bolts
(13) at
bottom of front bagger frame
(I4), hand
tightening
lock nuts (15).
.
Feed
front
bagger
frame
(14)
up
through
fabric
loops at front of bagger.
•
Snap bottom of front bagger
frame (14)
into
snap
feature
at front
of bagger
bottom.
•
Slide
bagger
fabric
loop segments
at
the ends of bag onto top bagger frame
tubing.
•
Slide two 1\4" hex
bolts (16) through
holes at top of the front bagger
frame
and thread
into nuts inside the tubing
of
top bagger frame..
•
Slide plastic clip (17) down into bagger
fabric loop on right side and snap to front
bagger
frame
(I4)
101 mm (4 inches)
from
top
of front
bagger
frame
tube.
°
Uninstall
lock nuts (21) at rear of top
bagger
frame
and at bottom
of front
bagger frame
and attach
cross braces
(22) on each side.
•
Reinstall
lock nuts (21) and tighten
until
fully seated.
•
Slide rubber
seal
(23) to top of metal
bagger handle
(24).
•
Slide bagger
handle
(24) down through
bagger cover and frame upper weldment
holes.
•
Slide
clevis
pin (25) through
hole
at
bottom
of
bagger
handle
and
slide
retainer
spring
(26) into hole at the end
of the clevis pin until it locks into place
PARA NIVEL
Aseg_rese de
ta PSI que se i
inflados o poc
bien cortado,
la SEGADOR
REGULACIO
1. Sitodoslc
inflados y
codado dq
cortadora
2.
Con una
regulabte
tuerca de
para bajaJ
h&gala gil
para subi_
NOTA: Cada
ajuste her& va
madamente 3
Haga girar la
tuerca f_acia!
la derecha
pare subir4a
segadora_
3.
Pruebe I_
c6sped q_
vando co
case nec,
satisfact#_
REGULAClOI
A LADO
1. Con todo
inflados, e
o en la en
CUIDADO:
las manos co_
con tela grue.,
2o Suba la S
3.
A ambos
cuchilla h_
que hay e
y el suelo.
a ambos I
4,. En caso q_
lea los pa_
laci6n Vis_
10
Publicidad
Tabla de contenido
