Cloer 4609 Instrucciones De Uso página 8

Dear Customer
We wish you much pleasure with your new
electric kettle.
Your Cloer Company
Description
1 Lid opening button
EN
2 Handle
3 Water level display, lighted up during
operation
4 ON/OFF button with indicator light
5 Spout
Preparation for use
·
Remove all packaging elements and labels, but
not the rating plate.
·
Place the electric kettle on a dry, even, non-slip
surface.
Before initial use
·
Please read these operating instructions care-
fully before using the device for the first time.
·
Shake out the water from the first boiling process.
Safety notices for use of the
contact base / electric kettle
The appliance meets the
requirements of the applicable
EC directives.
The appliance is intended for in
door use only.
·
Do not fill the electric kettle with water past the
MAX marking. Scalding may result from water
boiling over.
·
Always remove the electric kettle from the
contact base before filling with water.
·
This electric kettle may only be used for heating
water.
·
Use the electric kettle only with the provided
contact base.
·
Before operating the machine, make sure that
the contact base is dry.
·
Please make sure that water is never spilled on
the contact base.
·
If water is accidentally spilled onto the contact
base, proceed as follows:
– Unplug the unit from the wall socket.
– Dry the contact base with an absorbent
dry kitchen towel.
– Dry the surface beneath the contact base.
– Plug the unit into the wall socket again.
·
Never operate the electric kettle without
the lid closed and without lime filter, since
then the device will not shut off automatically
when the water boils.
CAUTION!
The surface is hot during
operation. Only touch the
8
device at its handle.
Operation
·
Plug the power plug into the wall socket.
·
Remove the electric kettle from the contact base.
·
Open the lid of the removable kettle by pressing
the button to open the lid.
·
NOTE: For your safety, the lid is equipped
with a locking device. If the electric kettle
is accidentally overturned during use, the lid will
not open. This reduces the risk of being scalded
by spilled water.
·
Fill the electric kettle with water.
·
Close the lid manually.
·
MAKE SURE not to fill water past the
maximum marking on the water level indicator
or not to fall below the minimum marking.
·
Place the electric kettle anywhere on the
contact base.
·
The unit is ready for operation now.
·
To switch it on, press the ON/OFF switch
on the bottom of the handle. The switch locks
into place and the water level display lights up.
·
When the water boils, the electric kettle
automatically switches off.
·
You can interrupt the boiling process at
any time by pushing up the ON/OFF switch.
·
To pour the water, lift the electric kettle
from the contact base.
·
IMPORTANT: Always make sure that the device
is switched off before removing the electric
kettle from the contact base.
Overheating protection device
The electric kettle is equipped with an over-
heating protection device. In the event that you
accidentally operate the electric kettle without
water or if the water level is too low, causing the
water to evaporate during boiling, the device
will automatically switch off for your safety. The
device will be ready to operate once it has been
filled with cold water.
Cleaning
·
CAUTION: Do not immerse appliance in water
and do not clean under running water!
·
Do not clean the electric kettle with heavily
abrasive cleaners. They could scratch the
appliance.
·
Clean very dirty appliances either with lukewarm
water or with a stainless steel cleaner.
·
If a stainless steel cleaner is used, make sure
that it is not aggressive and does not contain
chlorine or acids.
Care
·
Use a special stainless steel care product for minor
cleaning (water stains, light fingerprints, etc.).
·
CAUTION: Use only for the exterior! Do not use on
surfaces that come into contact with food (inside).
Decalcifying
·
If you have hard water, the electric kettle should
be decalcified regularly (depending on the
hardness of the water, about every 2 - 3 weeks).