Tabla de contenido
Publicidad
.dotes
During Assembly
Use
a
soft
platform below the
parts to avoid scratches and damages.
.
Please
note you install the panels
with
the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT")
and peel the film strip covering the panels.
.
Product dimensions
can be
adjusted to your specific
needs:
1.
The
wall-mounting profile (top-back)
can be
adjusted from 285
to
331
cm
(112.2" to 130.3")
above ground.
The
adjusting
is
done when measuring and drilling (Step
6).
Please
note the installation recommendations' height suggested
in
Diagram
A.
Please
note
that the product appearance
may
slightly change
as
a
result,
however snow
load
weight
does not change.
2. Poles
distance from the wall
are
adjusted
(due
to the wall mounting
plate's
height) from 254.4
to
267.4 cm (100.2" to 105.3").
Poles
distance from the
side
edges can be
adjusted from
5
to
54 cm
(2" to 21.3")
as
suggested
in
Diagram
B.
The
adjusting of the
poles sideways,
is
done after assembly and before anchoring (Step
23) by
sliding
poles at
the front
profiles'channel (Part 7040+7041).
3. Wall
mounting height
and the resulting distance from the wall
determine the
roof's angle and the total depth of the product
(distance
of gutter from the
wall). Higher wall
mounting
and shorter distance between wall and poles increase the roof angle and
shorten the total depth
as
suggested
in
Diagram
C.
Li3
Step:
Step 6:
It
is
important to
plan
the installation
area,
mark
as
per the instructions and level the surface
prior to the
assembly.
Make
sure
you
use
suitable
screws
and anchors.
Set
the mounting
plate's
height from 280 to
331
cm
(112.2" to 130.3").
The
poles'distance from the wall will vary
from 254.4
to 267.4
cm
(100.2" to 105.3")
as
a
result
of the height you've
set.
Step 12:
Please
apply silicone
sealants above beam
7288
+
7290,
in
order to prevent water from seeping
in.
Step 15: Make
sure
that the angle between the
back wall
profile and the panel supporting profiles
is
90
degrees.
Step 17:
Please
note you install the panels
with
the
UV
protected
side
out
(marked
with "THIS
SIDE
OUT")
and peel the film strip covering the panels.
Step 20b:
Please
apply silicone
sealants on
both
sides
of
the part combining 8071 & 8072
in
order to prevent
water
leakage,
as
shown
at
the
drawing
20b.
Step 21a:
Please
apply silicone sealants
on
the inner part
of 7997,
and connect to the profile
as
depicted
in
drawing
21b.
Step 21c:
Please
do not
tighten
screw
4043
yet,
in
order to allow the final adjustments done
in
step
23a.
Step 23a:
Please
adjust the
gutter
head's
angle according to your needs and
tighten
screws
4043.
Step 23b:
Please
adjust the
poles sideways by
sliding them to
their
final position prior to anchoring.
Make sure
that the
poles distance from
the
Patio
cover
side
edge does not exceed 54 cm/21.3".
Step 25: Anchoring this product to the ground
is
essential to
its
stability
and rigidity.
It
is
required to complete
this stage
in
order for your warranty to
be
valid.
*Tighten
all
screws
when completing assembly.
Note:
The
wall anchoring kit supplied
with
this product
is
suitable only for concrete
walls.
Other wall
types need
an
accordant wall fixation
kit.
285-331cm
112.2"-130.3"
A
5-54cm
2"-21.2"
5-54cm
2"-21.2"
5°-15°
Publicidad
Tabla de contenido
