Technical Data - Invisia Accent Ring Manual Del Usuario

OVERVIEW
Thank you for choosing the Invisia Accent Ring. Please read and
understand the instructions in this manual; keep manual for future
reference. It is your responsibility to see that your Invisia Accent Ring is
properly assembled, installed, and cared for. Failure to follow instructions in
this manual could result in serious injury or death. If you are not equipped
to undertake the outlined work, we would recommend that you have your
Invisia Accent Ring installed by a qualified contractor.
The Invisia Accent Ring is a circular grab bar designed to disguise safety in
a bathroom accessory. The Invisia Accent Ring is intended for moderate
vertical and horizontal load bearing to provide sitting and standing support
for people with reduced mobility. The Accent Ring is to be installed with
appropriate fasteners to a structural wall. The maximum user weight for
this product is 500lbs / 227kgs. Note: Product is not intended to support full
body weight. The Invisia Accent Ring is not to be used in any other way
than described above.
LIMITED LIFETIME WARRANTY
Products are covered by a limited lifetime warranty against defects in
materials and workmanship for the original purchaser. Warranty excludes
products that have been damaged through misuse, accidental damage,
alteration, normal wear and tear, wood material and stain, or the use of
corrosive or abrasive cleaning products.
Buyer hereby indemnifies, agrees to hold harmless and defend HealthCraft
Products Inc. from and against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including without
limitation consequential damages and reasonable professional fees)
resulting from buyers specification, application, or improper use of goods
described hereon; buyers omission or neglect. HealthCraft Products Inc.
does not assume any liability for damage resulting from services performed
by others or faulty installation, misuse or misapplication of goods sold by
HealthCraft Products Inc. HealthCraft Products Inc. shall not be liable for
prospective profits or special, indirect, or consequential damages, or for the
cost of any corrective work done without HealthCraft Products Inc. prior
approval. HealthCraft Products Inc. total liability hereunder shall in no
event exceed the purchase price of the goods specified hereon.
Specifications subject to change without notice.
HealthCraft Products Inc.
2790 Fenton Road
Ottawa, Canada
K1T 3T7
10
English
Gate 88
Kanalgatan 45B
Skellefteå, Sweden
EC REP
93123
DELIVERY CONTENTS / ACCENT RING
1. Accent Ring
2. Wall Stem Assembly (x4)
3. #10-32 Set Screw, S/S (x4)
4. Center Punch
5. 3/32" Hex Key
INSTALLATION WARNINGS
1. Rail must be installed to walls that are structurally sound. If desired
installation location does not have adequate structure, add wood blocking.
2. For different wall constructions, use appropriate fastener combination
(Note: reduced weight capacity when not full structure).
3. CAUTION - Do not install if structure behind walls is unknown.
4. CAUTION - Do not install into metal studs.
5. CAUTION - Do not install in fiberglass / acrylic shower enclosures with
insufficient stiffness and strength.
6. CAUTION - Rail and bathtub are slippery when wet.
SUGGESTED ACCENT RING LOCATIONS
To determine the optimal mounting location, we recommend holding the
rail in place and walking through the motions of a transfer (sitting,
standing, reaching, etc.). Recommended rail height 36-48" / 914-1219mm,
or centered around shower control valve.
INSTALLATION
1. Back off set screws from rail sockets.
2. Allow wall stems to freely move in and out of rail sockets.
3. Peel off label on back of wall stems to expose sticker.
4. With wall stems inside rail sockets, push the rail against the wall.
5. Firmly press the rail so stickers on back of wall stems contact wall.
6. Remove rail carefully so wall stems stay on the wall.
7. Using wall stems as locating guides, mark the tile with center punch.
8. Drill pilot holes for fasteners.
9. Fasten the wall stems to the wall using appropriate fasteners and
waterproofing.
10. Place rail back onto the fastened wall stems.
11. Secure rail to wall stems by tightening set screws. Inspect hardware
regularly, and tighten if required.

TECHNICAL DATA

See Figure E.
PRODUCT USAGE
See Figure F.
FIGURE A.
6. Lock Washer, S/S (x4)
7. #10 x 3" Wood Screw, S/S (x4)
8. 3/16" Bolt, S/S (x4)
9. Hollow Wall Anchor (x4)
FIGURE B.
FIGURE C.
FIGURE D.