Technical Data - Invisia FDS-S Manual De Instrucciones

OVERVIEW
Thank you for choosing the Fold Down Seat from Invisia. Please read and
understand the instructions in this manual; keep manual for future
reference. It is your responsibility to see that your Fold Down Seat is
properly assembled, installed, and cared for. Failure to follow instructions in
this manual could result in serious injury or death. If you are not equipped
to undertake the outlined work, we would recommend that you have your
Fold Down Seat installed by a qualified contractor.
The Fold Down Seat is a high quality, commercial grade, fold down shower
seat. The Fold Down Seat is intended to provide shower seating support
for people with reduced mobility. The Fold Down Seat is intended to bear
weight ONLY when the seat is in the down position; the seat is not
intended to bear weight in any other position. The Fold Down Seat is
intended to be folded up when not in use. The hinge allows the seat to
open slowly, and lock against the wall in the folded position. The Fold
Down Seat is installed with appropriate fasteners to a structural wall. The
maximum user weight for this product is 440lbs / 200kgs. Note: Product is
not intended to support full body weight (i.e. do not stand on the seat). The
Fold Down Seat is not to be used in any other way than described above.
ONE YEAR WARRANTY
Products are covered by a one year warranty against defects in materials
and workmanship for the original purchaser. Warranty excludes products
that have been damaged through misuse, accidental damage, alteration,
normal wear and tear, wood material and stain, or the use of corrosive or
abrasive cleaning products.
Buyer hereby indemnifies, agrees to hold harmless and defend HealthCraft
Products Inc. from and against any and all liabilities, claims, (founded and
unfounded), losses, damages, costs and expenses (including without
limitation consequential damages and reasonable professional fees)
resulting from buyers specification, application, or improper use of goods
described hereon; buyers omission or neglect. HealthCraft Products Inc.
does not assume any liability for damage resulting from services performed
by others or faulty installation, misuse or misapplication of goods sold by
HealthCraft Products Inc. HealthCraft Products Inc. shall not be liable for
prospective profits or special, indirect, or consequential damages, or for the
cost of any corrective work done without HealthCraft Products Inc. prior
approval. HealthCraft Products Inc. total liability hereunder shall in no
event exceed the purchase price of the goods specified hereon.
Specifications subject to change without notice.
HealthCraft Products Inc.
2790 Fenton Road
Ottawa, Canada
K1T 3T7
DELIVERY CONTENTS / PARTS
1. Seat
2. Bracket
3. #14 x 2.5" Wood Screw, S/S (x5)
10
English
Gate 88
Kanalgatan 45B
Skellefteå, Sweden
EC REP
93123
FIGURE A.
INSTALLATION WARNINGS
1. Seat must be installed to walls that are structurally sound.
2. If desired installation location does not have adequate structure, add
wood blocking.
3. CAUTION - Do not install if structure behind walls is unknown.
4. CAUTION - Do not install into metal studs.
5a. CAUTION - Do not install in fiberglass / acrylic shower enclosures with
insufficient stiffness and strength. 5b. Add wood blocking if required.
6. CAUTION - Ensure wood blocking behind wall supports entire footprint
of seat.
7. CAUTION - Do not use seat for purposes other than sitting.
8. CAUTION - Do not seat more than 1 person at a time.
9. CAUTION - Ensure seat is fully supported by bracket prior to sitting.
10. CAUTION - Pinch points present when folding seat.
11. CAUTION - Seat and bathtub are slippery when wet.
SUGGESTED FOLD DOWN SEAT LOCATIONS
To determine the optimal mounting location, we recommend consulting
with an appropriate healthcare professional. If side wall (to faucet) is less
than 36" / 914mm, seat can be mounted on the back wall. If side wall (to
faucet) is greater than 36" / 914mm, seat can be mounted on side wall
(less than 24" / 610mm from faucet wall). ADA recommend seat height
from finished floor 17-19" / 432-483mm.
INSTALLATION
1. Mark the location on the wall of the top hole of the bracket.
2. Drill pilot hole for fastener.
3. Fasten the bracket to the wall using appropriate fastener and
waterproofing.
4. Use a level to ensure the braket is level and mark location on the wall of
other hole.
5. Drill pilot hole for fastener.
6. Fasten the bracket to the wall using appropriate fastener and
waterproofing.
7. Repeat step 5 and 6 for remaining holes (x3).
8. Slide seat onto bracket completely.
9. Inspect hardware regularly, and tighten if required.

TECHNICAL DATA

See Figure E.
PRODUCT USAGE
See Figure F.
FIGURE B.
FIGURE C.
FIGURE D.