Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TE-CI 18 Li BL Manual De Instrucciones Original

6.2 Changeover switch (Fig. 4/Item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
hammer screwdriver and for preventing the cord-
less hammer screwdriver from being switched on
inadvertently. You can select between clockwise
and counterclockwise rotation. To avoid causing
damage to the gearing, the direction of rotation
must only be changed when the equipment is at
a standstill. When the slide switch is in the middle
position, the On/Off switch is blocked.
6.3 On/Off switch (Fig. 4 / Item 4)
Infinitely variable speed control is possible with
the On/Off switch. The further you push the
switch, the higher the speed of the cordless ham-
mer screwdriver.
To switch on:
Press the On/Off switch (4).
To switch off :
Release the ON/OFF switch (4).
6.3 On/Off switch (Fig. 4 / Item 4)
Infinitely variable speed control is possible with
the On/Off switch. The further you push the
switch, the higher the speed of the cordless
screwdriver.
6.4 Battery capacity indicator (Fig. 5 – Item 2)
Press the battery capacity indicator switch (a).
The battery capacity indicator (2) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
Anl_SA_TE_CI_18_Li_BL_Solo.indb 36 Anl_SA_TE_CI_18_Li_BL_Solo.indb 36
GB
6.5 LED lamp (Fig. 6/Item 7)
The LED lamp (7) can be used in poor lighting
conditions to illuminate the area where you want
to screw. The LED light (7) will come on automati-
cally as soon as you press the On/Off switch (4).
6.6 Changing the bit (Fig. 7)
Important! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless hammer screwdriver.
Inserting the bit:
• Insert the bit into the bit mount (1) as far as the
stop while simultaneously pulling the sleeve on
the bit mount (1) toward the bit
• Release the sleeve again.
• Check that the bit is securely seated.
Removing the bit:
• Pull the sleeve on the bit mount (1) toward the
bit, hold it tight and remove the bit.
6.7 Screws
It is advisable to use self-centering screws
(e.g.Hex, cross recessed head) as these will ena-
ble you to work safely and reliably. Always make
sure that the bit used is of the same size and sha-
pe as the screw.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
- 36 -
09.02.2021 14:07:29 09.02.2021 14:07:29