Publicidad
Enlaces rápidos
E
ENGLISH USER INSTRUCTIONS & PARTS LISTING PARTES
Model
SM1050-2P
Voltage: 220
Phase: 1
Cycles: 50/60
Variable Speed
to 5000 RPM
SM1050-2P ENDURO
Copyright © 2013 Enduro
nduro
SM1050-2P & SM1050-2PF
SERVO MOTOR WITH POSITIONER
TM
SM1050
ELITE
™
Servo Motor
™
www.endurosaves.com
ELITE
Model
SM1050-2PF
Voltage: 220
Phase: 1
Cycles: 50/60
Variable Speed
to 5000 RPM
SM1050-2PF ENDURO
INSTRUCTIONS - PAGE 2 >
PARTS LISTING - PAGE 14 >
TM
TM
SM1050
ELITE
™
Publicidad
Resumen de contenidos para Enduro ELITE SM1050-2P
- Página 1 Cycles: 50/60 Cycles: 50/60 Variable Speed Variable Speed to 5000 RPM to 5000 RPM SM1050-2P ENDURO ELITE SM1050-2PF ENDURO ELITE ™ ™ INSTRUCTIONS - PAGE 2 > PARTS LISTING - PAGE 14 > Copyright © 2013 Enduro Servo Motor ™ www.endurosaves.com...
- Página 2 It even works well in environments with an unstable electrical power supply. The positioner motor comes with a positioner sensor kit included. With correct installation and settings, Enduro Elite SM1050-2P can provide accurate Needle Positioning of either the UP or DOWN position ™ every time. In addition to Needle Positioning, Enduro Elite SM1050-2PF provides Foot Lift output which ™...
- Página 3 ENGLISH - 3 Installation Put the mounting bracket of the motor upwards to the bottom of the tabletop and fix the motor to the tabletop with the bolts provided. Connect the treadle rod with the connecting rod joint. Install the female plug of the cable from the switch box into the power inlet socket in the back of the motor box.
- Página 4 4 - ENGLISH Motor Rotating Direction Setting Setting up Number 2 a. Keep "▼" button pressed for several seconds, until LED display indicates "SET.0". b. Press "▲" button 2 times. It will now indicate "SET.2", which means "Setting up No. 2". c.
- Página 5 ENGLISH - 5 Option A - Setting Slow Starting Speed via Motor Control a. Keep "▼" button pressed for several seconds, until LED display indicates "SET.0". b. Press "▲" button 1 time to indicate "SET.1", which means "Setting up No. 1". c.
- Página 6 6 - ENGLISH Maximum Speed Setting Setting up Number 3 a. Keep "▼" button pressed for several seconds, until LED display indicates "SET.0". b. Press "▲" button 3 times to indicate "SET.3", which means "Setting up No. 3". c. Then press "▼" button and LED shows 100-5000, which means the highest motor speed in RPM.
- Página 7 ENGLISH - 7 Installation of Positioner on SM1050-2P and SM1050-2PF 1. Be sure the female power cord is disconnected from the power inlet socket. 2. Remove the screw on the machine pulley. Install the sensor adapter (supplied) onto the pulley with the adapter screw (supplied).
- Página 8 There are various types of electro mechanical and electro magnetic foot lifts available which either come with the sewing machine or can be retro fitted to the machine. Consult the dealer where you purchased your Enduro™ 1050-2PF Motor for additional information. www.endurosaves.com...
- Página 9 ENGLISH - 9 Heel Back Needle Position Setting For Motors with Foot Lift (Enduro SM1050-2PF) ™ Setting up Number 4 a. Keep "▼" button pressed for several seconds, until LED display indicates "SET.0". b. Press "▲" button 4 times. It will now indicate "SET.4", which means "Setting up No.
- Página 10 10 - ENGLISH Error Messages and Trouble Shooting When an error message appears on the display the motor will stop automatically to protect the electronics of the motor and most importantly, to protect the motor circuit board. If an error message occurs be sure to repeat the action that caused the error message. Many times if you reactivate the treadle and start the motor again, the error message will clear indicating this was a False error message requiring no further action.
- Página 11 ENGLISH - 11 E2: Motor Phase Signal Error (Hall Sensor Error) It is possible to receive an E2 error message from unstable power which means it is a False error and the problem should resolve on its own. Check the Hall sensor signal connector and socket (HER indicated) on the circuit board (Five Pin connector / socket), to make sure the 5 wires are connected to the board properly.
- Página 12 12 - ENGLISH E6: Pedal Position Sensor Error It is possible to receive an E6 error message from unstable power which means it is a False error and the problem should resolve on its own. While the motor is on and the pedal position signal received by the motor circuit board is abnormal, it is possible to get the E6 error message.
- Página 13 ENGLISH - 13 Treadle Sensor Installation Description with Diagrams (Proper Replacement of Treadle Sensor) 1. Remove the 4 screws on the treadle sensor 2. Check the channel sensor. It should have plate. a red light when the cable is connected to the motor circuit board and the motor is powered on.
- Página 14 ENGLISH - 14 SM1050-2P & SM1050-2PF PARTS LISTING Fig. Description SM76 Sensor only with screws (dual channel for motors with positioner) SM104 Treadle sensor plate assembly complete with 4 screws (dual channel for motors with positioner) (877C) SM77 Replacement positioner sensor kit complete SM78 Complete horizontal wire harness for 220 volt models (431C) SM123...