Stanley HLWAKS Manual De Instrucciones página 3

"Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials
such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually
prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly
protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and
well insulated from materials that could contact them and cause a short circuit. "
INStRUCtIONS PERtAININg tO WAtERPROOF HEADlAMPS
The rubber O-ring acts to preserve the waterproof qualities of the headlamp. The O-ring contacts the battery compartment cover
to prevent water from entering the gap. An undamaged rubber O-ring, rubber bezel and lens, and proper sealing of the battery
compartment before use are very important.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Attempting to remove the rubber O-ring; use of the unit with a damaged O-ring, rubber bezel or lens; improper sealing of the
waterproof battery compartment; and/or submerging this unit in depths greater than 3 feet may cause the unit to no longer be
waterproof. Do not submerge the unit if these conditions exist or the unit could sustain permanent damage.
• Submerging this unit in depths greater than 3 feet and/or operating it in water temperature other than between 41ºF and 104ºF
(5ºC and 40ºC) could result in leakage, warping or malfunction, causing permanent damage to the headlamp.
SAVE tHESE INStRUCtIONS
INtRODUCtION
Congratulations on purchasing your new Stanley Waterproof LED Headlamp. Read this Instruction Manual and
follow the instructions carefully before using your new headlamp.
POWER SUPPly
The unit is powered by four "AAA" alkaline dry cell batteries (may be sold separately) inside the battery compartment.
Replacing the batteries
1. Using a coin, screwdriver, or other appropriate tool, unscrew the groove at the top of the battery compartment cover
(counterclockwise) and remove it.
2. Insert batteries as described in compartment, observing the cautions that follow.
3. Replace the battery compartment cover by first aligning the screw hole of the battery compartment cover to fit over the screw
post of the battery compartment.
4. Using a coin, screwdriver, or other appropriate tool, screw the groove at the top of the battery compartment cover in a
clockwise direction to secure. Do NOT overtighten.
Note:
Use only "AAA" alkaline dry cell batteries in this unit.
CAUTIONS
• When replacing the "AAA" alkaline dry cell batteries: DO NOT mix old and new batteries. Always insert batteries correctly with
regard to polarity (+ and –), marked on the battery and the battery compartment. Remove dead batteries immediately and
dispose of per local codes.
• Follow all warnings regarding batteries in the Important Safety Instructions section of this manual.
OPERAtINg INStRUCtIONS
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Never operate this headlamp unless the rubber O-ring, rubber bezel and lens are intact and properly seated; and the waterproof
battery compartment cover is securely in place.
• Never operate this headlamp at water depths greater than 3 feet.
• Never operate this headlamp in water temperatures other than between 41ºF and104ºF (5ºC and 40ºC).
• This headlamp is designed to operate for up to one hour under water.
HLWAKS_HLWAKSL_ManualENSP_071012.indd 4-5
4
Operating the headlamp
1. Place the headlamp on your head and adjust the strap to fit your head securely.
2. Turn the headlamp on by rotating the Power/Brightness Selector Knob clockwise
or counterclockwise to the desired mode (using the embossed Dot Icon as a
reference point).
The headlamp offers the following lighting modes when rotated clockwise:
Mode 1: The 6 auxiliary LED bulbs will light alone.
Mode 2: The 3 watt LED bulb will light alone at medium brightness.
Mode 3: The 3 watt LED bulb will light alone at its maximum brightness.
Mode 4: The 3 watt LED bulb and the 6 auxiliary LED bulbs will all light.
Mode 5: Turns the headlamp off.
IMPORTANT:
• When the Power/Brightness Selector Knob is rotated counterclockwise, the mode selection sequence is reversed.
• When not in use or stored, always rotate the Power/Brightness Selector Knob to the Off Mode position.
• The headlamp body is connected to the battery compartment through an integrated cord. Do not damage the integrated cord or
attempt to disconnect it from the either headlamp body or from the battery compartment at any time.
• The headlamp body is detachable from the head strap. However, manufacturer strongly recommends that you not detached it
unless absolutely necessary.
• To avoid sustaining damage, this headlamp should not be used under water for any longer than one hour.
Operating the Nighttime safety flasher
The nighttime safety flasher located on the battery compartment is controlled by the adjacent On/Off pushbutton. Refer to the
"Features" section at the beginning of this manual to locate. Always switch it off when not in use and when the headlamp is being
stored.
Pivoting the headlamp main body
The headlamp body allows the headlamp to be tilted forward and backward to adjust
the area of illumination.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
The headlamp body was designed to tilt forward and backward only. Do not attempt
to "force" the headlamp body beyond its maximum angle.
tROUBlESHOOtINg
Unit will not operate
1. Make sure the Power/Brightness Selector Knob is not rotated to the Off Mode position.
2. The battery compartment cover may be loose. Screw it clockwise using a coin, screwdriver or appropriate tool to secure. Be
careful not to over-tighten.
3. The batteries may be installed with incorrect polarity (+ and –). Follow the directions marked on the batteries and inside the
battery compartment.
4. The batteries may be completely discharged. Replace the batteries following the directions given in this manual.
5. If the headlamp does not operate after replacing the batteries as directed, contact manufacturer at (877) 571-2391.
CARE AND MAINtENANCE
Make sure the unit is thoroughly dry before storage. If the unit has been submerged, wipe it dry with a soft cloth.
If the unit gets dirty, gently clean the outer surfaces of the headlamp with a soft cloth moistened with a mild solution of water and
detergent.
ACCESSORIES
Recommended accessories for use with your tool are available from the manufacturer. If you need assistance regarding accessories,
please contact the manufacturer at (877) 571-2391.
WARNING: The use of any accessory not recommended for use with this appliance could be hazardous.
EMBOSSED DOT ICON (FOR REFERENCE WHEN SELECTING
LIGHTING MODE)
5
7/10/2012 11:13:51 AM