Stanley HBHL1S Manual De Instrucciones

x
RECHARGEABLE LED HEADBAND
LIGHT
INSTRUCTION MANUAL
1
4
3
2
7
9
SAVE THIS INSTRUCTION MANUAL FOR FUTURE
REFERENCE.
© 2017 Baccus Global LLC
Baccus Global LLC, Boca Raton, FL 33432
(877) 571-2391
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void
user's authority to operate the equipment.
SAFETY GUIDELINES / DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not
avoided, may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be
followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or
equipment could result in serious injury and property damage. There are certain applications for which tools
and equipment are designed. Manufacturer strongly recommends that this product NOT be modified and/
or used for any application other than for which it was designed. Read and understand all warnings and
operating instructions before using any tool or equipment.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating light. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
WARNING: This product or its power cord contains lead, a chemical known to the State of California to
cause cancer and birth defect or other reproductive harm. Wash hands after handling.
• For household use only.
• Do not incinerate.
HBHL1S_ManualENSP_111517.indd 1
HBHL1S
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
WARNING – WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
• To reduce the risk of injury, close supervision is necessary when the light is used near children.
• Use only attachments recommended or sold by the manufacturer.
SPECIFIC SAFETY INSTRUCTIONS FOR CHARGING THIS UNIT
WARNING – TO REDUCE THE RISK OF ELECTRIC SHOCK:
• Charge indoors only.
• Do not expose the built-in USB Charging Connector to moisture, water or any other liquid.
• Use only the built-in USB Charging Connector supplied by the manufacturer to recharge.
• Make sure the light is turned off before connection to a power source.
• If an external adapter is used as a USB power source, make sure it is a Class 2 power unit.
CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• The light should be turned off when charging or not in use.
• Never place the light face down on any surface when charging.
• Make sure the USB Connector Protective Cover and the USB Charging Connector are clean and free of
debris.
• Do not touch the electrical contacts on the USB Charging Connector. Fingerprints may affect conductivity.
• Failure to keep the battery charged will cause permanent damage and result in poor performance.
• Make sure the USB Charging Connector is covered by the USB Connector Protective Cover all the time
when the unit is stored or not in use.
SPECIFIC SAFETY INSTRUCTIONS FOR OPERATING THE
LIGHT
WARNING – FIRE HAZARD:
• Keep headband lamp away from materials that may burn.
• Do not expose this unit to extremely high temperatures, sparks or flames.
CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Do not place or immerse the light in water or other liquid. Do not place or store the light where it can
fall or be pulled into water or become wet. Detach the light from the headband before washing the
headband.
• The LEDs get hot quickly. Do not touch the hot lens, guard or enclosure.
• Never place the light face down on any surface when lit, charging or not in use. Never store the light
face down on any surface.
5
• Never look directly into the light or shine the light into another person's eyes.
• Keep sharp objects away from lens — it can crack or break.
• Do not drop or throw the headband lamp. It contains a lithium-ion battery.
• Do not open the light body casing. There are no user-serviceable parts inside.
• Do not operate the light without the lens in place.
• When not in use, the appliance should be stored in a dry, well ventilated place out of the reach of
6
children.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION
BATTERIES
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO
PERSONS OR PROPERTY:
Lithium-ion batteries are small, compact and ideal for providing long-lasting power to this unit. However,
they must be used and charged properly. Improper use can result in serious injury, fire, or death.
• Lithium-ion batteries can explode in the presence of a source of ignition. Do not use the product in the
presence of an open flame.
• Do not place this lithium-ion battery powered unit in fire or apply heat to it.
• Do not subject this lithium-ion battery powered unit to strong impacts or shocks. The battery in this
unit contains safety and protection devices which, if damaged, may cause the battery to generate heat,
8
rupture or ignite.
• Do not expose the lithium-ion battery to water or salt water, or allow the battery to get wet.
• Avoid storing this lithium-ion battery powered unit in the basement, bathroom or other areas of the
house that are or may become wet or where humidity and moisture may concentrate.
• Do not leave this lithium-ion battery powered unit in direct sunlight, or use or store the unit inside cars
in hot weather. Doing so may cause the battery to generate heat, rupture, or ignite. Using the battery in
this manner may also result in a loss of performance and a shortened life expectancy.
• Never charge this unit near heat or flammable objects.
• NEVER THROW WATER ON A BURNING LI-ION BATTERY! If a lithium-ion battery does catch on
fire, it will burn even more violently if it comes in contact with water or even moisture in the
air. A fire extinguisher must be used.
BC
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully charge it before using it for the first time.
When stored at room temperature with a full charge, Li-ion batteries will begin to discharge from the time
they are manufactured, even when unused. Deep discharges also decrease their capacity. Battery life can be
extended by the following:
• Charge battery to full capacity before storage.
• Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).
• Never discharge the battery fully.
• Charge after each use.
• Always charge at least once every 3-6 months if not in frequent use to prevent overdischarge.
Transportation of Lithium-Ion Batteries
• Always check all applicable local, national, and international regulations before transporting a unit
containing a Lithium-Ion battery.
• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be specifically limited or
prohibited.
INSTRUCTIONS PERTAINING TO THE WEATHER-RESISTANT
HEADBAND LIGHT
The USB Connector Protective Cover acts to preserve the weather-resistant qualities of the light. The
USB Connector Protective Cover covers the unit's built-in USB Charging Connector to prevent water from
entering the gap. An undamaged lens and Power Button, and proper sealing of the USB Connector
Protective Cover before use are very important.
CAUTION – TO REDUCE THE RISK OF PROPERTY DAMAGE:
Use of the unit with a damaged lens or Power Button, improper sealing of the USB Connector Protective
Cover, and/or submerging the light in water may cause the light to no longer be weather-resistant. Do not
use the light if these conditions exist or it could sustain permanent damage.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Stanley Rechargeable LED Headband lamp. Read this
Instruction Manual and follow the instructions carefully before using your new light.
FEATURES
1. Adjustable, Reversible Headbands
2. USB Connector Protective Cover
3. USB Charging Connector
4. Red Charging LED Indicator
5. Removable, Rechargeable Light with 6 Ultra Bright LEDs
6. Multi-function Power Button (High / Low / Flash / Off)
7. Green Charged LED Indicator
8. Keychain Ring Holder
9. Perspiration Barrier Comfort Strips
CHARGING/RECHARGING
This unit is shipped in a partially charged state. Fully charge the unit after purchase and before first
use using built-in USB Charging Connector for a full 3 hours or until the Green Charged LED Indicator lights.
Recharge after each use until the Green Charged LED Indicator lights.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged at least
every 3 to 6 months.
Procedure
1. Make sure the light is detached from the headband and is turned off.
2. Remove the USB Connector Protective Cover.
3. Insert the USB Charging Connector into a working USB power port. The Red Charging LED Indicator
will light to indicate the unit is in charging.
Note: Make sure the two electrical contacts on the built-in USB Charging Connector properly contact
the USB power port's contact pins (the Red Charging LED Indicator will light). Reverse the USB
Charging Connector if they do not.
4. Charge until the Green Charged LED Indicator lights.
5. When charging is complete, disconnect the USB Charging Connector from the USB power port. Replace
the USB Connector Protective Cover. Make sure it fits securely as it acts to preserve the weather-
resistant qualities of the headband light.
OPERATING INSTRUCTIONS
Assembling the Headband Lamp
The unit is provided with two same-sized reversible headbands for a total of four different colors. Fit the
unit into the center grooves on one of the headbands. Place the headband light on your head and adjust
the headband strap to fit securely. Operate the light as outlined in the following section.
Operating the Light Cordless
The headband light is controlled by the Multi-function Power Button at the center of the light. To operate
the light in cordless mode, disconnect the built-in USB Charging Connector from the device's USB Power
Port, and then select the desired light mode by pressing the Multi-function Power Button.
• Press once for high intensity.
• Press again for low intensity.
• Press a third time for the flashing LEDs.
• Press a fourth time to turn the lights off.
Note: If the light's internal battery level is too low, the built-in low voltage protection may activate after
a short period of operation, then the light will automatically shut down. This is a special feature to
protect the internal lithium-ion battery from damage. Recharge the battery before continuing use.
Operating the Light Corded
To operate the unit in corded mode, detach the light from the headband strap, remove the USB Connector
Protective Cover from the unit and then insert the unit's built-in USB Charging Connector into a device's
functional USB power port as described in the "Charging/Recharging" section. Operate the light as outlined
in the previous section.
IMPORTANT: The light will operate while the built-in USB Charging Connector is inserted into a working
USB power port, but will continue to draw power from the unit's internal battery. This may cause the low
voltage protection to activate and shut the light off. Manufacturer recommends only operating the unit
corded for a short period of time.
CARE AND MAINTENANCE
If the light gets dirty, gently clean the outer surfaces with a soft cloth lightly moistened with a mild solution
of water and detergent. The headbands can be hand-washed and allowed to air dry.
WARNING: Make sure the USB Connector Protective Cover is firmly in place when wiping off the
light; and make sure you have detached the light from the headband before washing the headband. Never
expose the USB Charging Connector to water or any other liquid or the risk of electric shock or permanent
damage to the light can occur..
TROUBLESHOOTING
The light will not charge
• Check that the light is turned off.
• Check that the built-in USB Charging Connector is properly inserted into a device's USB power port.
Confirm that the USB port is working and make sure there is good contact.
• Check that the built-in USB Charging Connector is clean and free of fingerprints.
The light will not operate cordless
• Make sure the Multi-function Power Button is pressed to turn the light on.
• The internal battery may be completely discharged. Charge the unit following the directions.
• If the unit does not operate after recharging as directed, contact manufacturer at (877) 571-2391.
The light will not operate corded
• Make sure the Multi-Function Power Button is pressed to turn the light on.
• Check that the built-in USB Charging Connector is properly inserted into a device's USB power port.
Confirm that there the USB power port is working and make sure there is good contact.
• The light will operate while the built-in USB Charging Connector is inserted into a device's functional
USB power port, but will continue to draw power from the unit's Lithium-Ion battery. The light may not
operate because the battery may be completely discharged. Charge the unit following the directions
given in this manual.
ACCESSORIES
Recommended accessories for use with your tool may be available from the manufacturer. If you need
assistance regarding accessories, please contact the manufacturer at (877) 571-2391.
WARNING: The use of any accessory not recommended for use with this appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer
at (877) 571-2391.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period of ONE
(1) YEAR from the date of retail purchase by the original end-user purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the defective product can
be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or
replacement at manufacturer's option. Proof of purchase may be required by manufacturer. (2) Return
the product to the retailer where product was purchased for an exchange (provided that the store is a
participating retailer). Returns to retailer should be made within the time period of the retailer's return
policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be required. Please
check with the retailer for their specific return policy regarding returns that are beyond the time set for
exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear
and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect,
misuse, abuse; and failure to follow instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights
which vary from state to state or province to province. This product is not intended for commercial use.
Please complete the Product Registration Card and return within 30 days from purchase of the product to:
Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432. Baccus
Global LLC, toll-free number: 1-877-571-2391.
SPECIFICATIONS
Input: 5V DC, 0.15A
Bulb: 6 ultra bright LEDs
Battery: Lithium-Ion, 3.7V DC
Imported by Baccus Global LLC,
One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432
www.Baccusglobal.com 1-877-571-2391
RD111517
11/15/2017 8:40:38 PM