Preparing To Work - Fimar NANO Manual De Uso Y Mantenimiento

safety of the appliance.
• When the appliance is not being used,
it should not be left connected to the
mains power supply.
• The manufacturer cannot be held liable
for any damage to persons, animal or
objects deriving from improper and
unreasonable use, and in any event
not complying with the instructions
mentioned above.
• For scrapping, follow the regulations in
force in the country.
• Do not use the vacuum cleaner with
the power cable twisted around the lid.
• Before connecting the appliance to
the electricity socket, make sure the
electrical information on the plate
corresponds to that of the mains
supply. The appliance must only be
powered by alternating current and
with a voltage equal to that shown
on the serial number plate.
WARNING:
• The power supply cable outlet must
have an earth connection in compliance
with the regulatory standards.
• Never vacuum
explosive or inflammable powders,
nor non-diluted acids and solvents!
These include gasoline, paint thinners
and fuel oil (which, when mixed with
the vacuum air, can form explosive
vapours or mixtures), and also non-
diluted acids and solvents, acetones,
aluminium and magnesium powders.
These substances may also corrode
the materials used to construct the
appliance.
• If the appliance is used in dangerous
areas (for example, gas stations), the
relative safety standards should be
observed. The appliance must never be
used in environments with a potentially
explosive atmosphere.
• Do not place any liquid containers on
the appliance.
UM_Nano_verAB.indd 7
gas, liquids or
• In the event of a fire, use a powder
extinguisher. Do not use water.
• If the appliance does not work properly,
check this is not caused by failure
to carry out routine maintenance.
Otherwise, ask for intervention of the
authorised technical assistance centre.
• If you need to replace any components,
request the ORIGINAL spare parts
from an Authorised Retailer or dealer.
• Do not wash the appliance with direct
water jets or with pressurised water,
nor with corrosive substances.

PREPARING TO WORK

Before beginning to work for the first time, it is necessary to:
1. Place the lower part of the outer packaging in contact with the floor.
WARNING: Use the pictograms printed on the box as reference.
2. Open the outer box.
3. Remove the accessories from the box and carefully lay them on the ground.
4. Remove the appliance from the packaging using the handle designed for this purpose
(Fig.1).
5. Remove the appliance from the protective bag using the handle designed for this purpose.
WARNING: it is recommended that all the packaging components be kept for any future
transportation of the appliance.
WARNING: these operations must be carried out using protective gloves to avoid any
possible contact with the edges or tips of metal objects.
6. Fix the rear wheel on the rear wheel support, insert the rear wheel pin into the slot of the
support (Fig.2).
WARNING: The wheel is correctly positioned when the stops of the wheel are completely
inside the slot of the support.
7. Insert the rear wheel supports onto the tank of the vacuum cleaner, insert the support pins
into the slots of the tank (Fig.3).
WARNING: To facilitate this operation on both the tank and on the supports, the letters
"R" and "L" are printed to indicate right and left.
8. Fix the rear wheel supports on the vacuum cleaner tank using the supplied screws (Fig.4).
WARNING: the screwdriver is not supplied.
9. Secure the pivoting wheel on the vacuum cleaner tank, insert the pivoting wheel pin in the
support hole (Fig.5).
WARNING: The pivoting wheel is correctly positioned when the stops of the wheel are
completely inside the slot of the tank.
WARNING: before using the appliance, make sure it is in order and safe to use with the
work equipment, especially the power cable and the extension cable. If everything is not
in order, the appliance must not be used.
10. Insert the vacuum hose from the vacuum nozzle present in the collection tank, to lock the
vacuum hose inside the nozzle rotate it according to the direction of the arrow (Fig.6).
WARNING: Refer also to the symbols printed on the device itself.
11. Assemble the steel extension tube (Fig.7).
12. Insert the extension tube into the vacuum hose (Fig.8) .
13. Insert the selected accessory into the extension tube (Fig.9).
14. Release the vacuum cover retaining hinges on the side of the tank (Fig.13).
WARNING: Refer also to the symbols printed on the device itself.
15. Using the handle on the vacuum tank cover, (Fig.1), remove the vacuum tank cover from the
collection tank. Put the vacuum tank lid gently on the floor.
16. Take out the air intake filter from inside the collection tank (Fig.14).
17. Insert the paper filter bag inside the collection tank, taking care to insert the filter correctly
into the vacuum nozzle inside the collection tank and making sure not to damage the
cardboard support in the bag itself (Fig.15).
WARNING: operation valid only if the optional paper filter bag is used.
18. Using the handle on the vacuum tank lid, position the vacuum tank lid on the collection tank.
19. Secure the suction cover stop hinges, located at the side of the tank.
WARNING: Never use the unit without the supplied vacuum motor inlet air filter.
20. Insert the plug of the power supply cable in the mains socket (Fig.10).
21. Turn on the appliance by pressing the main switch (Fig.11).
7
6/16/2016 2:45:39 PM