Lakos Twist II Clean T2C-075 Guía De Instalación Y Funcionamiento

II
TWIST
Installation Instructions for: 3/4-inch Model T2C-075
Pre-Installation Checklist
A. Select a good filter location:
Install on the pressure (outlet) side of any pumps and
pressure tanks
In a vertical position with Purge Exit pointing down
Away from extreme weather conditions to protect
from freezing
At least 12 inches away from walls or obstructions,
so top handle can be twisted
Allow enough clearance beneath the unit to:
(a) attach a purge drain hose to the Purge Exit
(recommended)
(b) remove the clear bowl assembly, to allow
replacement of element as needed
B. As a sunny outdoor installation might lead to algae
growth inside the clear bowl and affect the operation
II
of your TWIST CLEAN, an optional Sun Shield is
available.
Maximum Flow Ranges:
• T2C-075 ¾" Inlet/Outlet: 0 to 25 US gpm (0 to 5.7 m³/hr)
• T2C-100 1" Inlet/Outlet: 0 to 39 US gpm (0 to 8.9 m³/hr)
• T2C-150 1 1/2" Inlet/Outlet: 0 to 78 US gpm (0 to 17.7 m³/hr)
Maximum Pressure:
• 100 psi at 73˚F (6.9 bar at 38˚C)
Temperature Range:
• 32˚F - 120˚F (0˚C - 49˚C)
Mesh Sizes:
• 30 Mesh (600 Micron) Element (Brown)
• 60 Mesh (250 Micron) Element (White)
• 100 Mesh (150 Micron) Element (Gray)
• 140 Mesh (105 Micron) Element (Black)
• 200 Mesh (74 Micron) Element (Blue)
Top Handle
Red Safety Latch
Inlet
Flow Direction Arrow
Mounting
Eyelets
Clear Bowl
Filter Element
Dimensions
CLEAN
1-inch Model T2C-100
1 1/2-inch Model T2C-150
Width
Outlet
Purge Exit
Total
Installation and
Operation Guide
Installation In
7 Easy Steps
II
1. Remove the TWIST CLEAN
from its box. Check to make
sure the box also contains a
small dispenser of Teflon tape
and two slip/threaded adapters
for use if needed.
2. Be sure the clear bowl is
securely tightened (hand tighten
only). The unit is shipped with
the bowl loose. Lift the red
safety latch and rotate the top
handle a few times to make
sure it will rotate 1/4 clockwise
turn.
3. Prepare the piping manifold
II
to install TWIST CLEAN.
Select the best fittings for
your installation, using slip
or threaded fittings as desired.
Notice the direction of water
flow through the unit -- a flow
direction arrow is molded into
the side of the unit. (Fig A).
4. Use proper PVC solvents and
follow gluing instructions on solvent container. Do not
spill solvent on any part of the TWIST
5. Mounting eyelets provide for a more stable installation (Fig
B). Stabilizer bolts are recommended for long term stability
II
of your TWIST CLEAN. Use ⅜" Hex Lag Screws plus
washers and PVC pipe to connect to a secure surface.
These parts are NOT supplied with your TWIST
6. Once installed, test by turning water supply on slowly,
allowing water to feed through the unit. Check for
leaks. After lifting the safety latch, twist the top handle
with a ¼ clockwise turn to re-direct the flow for cleaning.
This should lift the screen element inside the bowl and
release flush water through the Purge Exit at the bottom of
the unit. Twist the handle back to its "run" position, lower
the safety latch and check for leaks.
7. Attach a flush drain hose (if necessary) to direct the
purged particle matter and excess water to a drain or other
desired area for discharge (Fig C).
Optional Accessories
Sun Shield For Outdoor Installations
Black neoprene woven cover, slips over bowl
to prevent growth of algae and other organics.
Model Size
T2C-075 (¾")
T2C-100 (1")
T2C-150 (1-½")
SUN SHIELD
Fig A
Fig B
Purge Exit
Hose
Fig C
II
CLEAN unit.
II
CLEAN.
Sun Shield Part Number
131355
132240
LS-866B (Rev. 5/13)