Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
16 user interface
[01]
Set correct password
[02]
Enter Advanced setup menu?
[03]
Select Temperature input
Select Potentiometer input
Select Linear resistance input
Select Current input
Select Voltage input
[04]
Select 0.0-1 V input range
Select 0.2-1 V input range
Select 0-5 V input range
Select 1-5 V input range
Select 0-10 V input range
Select 2-10 V input range
[05]
Select 0-20 mA input range
Select 4-20 mA input range
[06]
Select 2-Wire sensor connection
Select 3-Wire sensor connection
Select 4-Wire sensor connection
[07]
Set Resistance value low
[08]
Set Resistance value high
[09]
Select Celsius as temperature unit
Select Fahrenheit as temperature unit
[10]
Select TC sensor type
Select Ni sensor type
Select Pt sensor type
[11]
Select Display unit
[12]
Select Decimal point position
[13]
Set Display range low
[14]
Set Display range high
[15]
Select Relay setpoint in % of input range
Select Relay setpoint in display units
[16]
Select Pt10 sensor type
Select Pt20 sensor type
Select Pt50 sensor type
Select Pt100 sensor type
Select Pt200 sensor type
Select Pt250 sensor type
Select Pt300 sensor type
Select Pt400 sensor type
Select Pt500 sensor type
Select Pt1000 sensor type
[17]
Select Ni50 sensor type
Select Ni100 sensor type
Select Ni120 sensor type
Select Ni1000 sensor type
[18]
Select TC-B sensor type
Select TC-E sensor type
Select TC-J sensor type
Select TC-K sensor type
Select TC-L sensor type
Select TC-N sensor type
Select TC-R sensor type
Select TC-S sensor type
Select TC-T sensor type
Select TC-U sensor type
Select TC-W3 sensor type
Select TC-W5 sensor type
Select TC-Lr sensor type
9116 Universal converter
Version No. V3R0
[19]
Select OFF function - relay is permanently off
Select POWER function - relay indicates power
status OK
Select ERROR function - relay indicates sensor
error only
Select WINDOW function - relay is controlled by 2
setpoints
Select SETPOINT function - relay is controlled by 1
setpoint
[20]
Select Normally Closed contact
Select Normally Open contact
[21]
Set Relay setpoint
[22]
Select Action on decreasing signal
Select Action on increasing signal
[23]
Set Relay hysteresis
[24]
Select No error action - undefined status at error
Select Open relay contact at error
Select Close relay contact at error
Select Hold relay status at error
[25]
Set Relay ON delay in seconds
[26]
Set Relay OFF delay in seconds
[27]
Select Contact is Closed Inside Window
Select Contact is Open Inside Window
[28]
Set Relay window setpoint low
[29]
Set Relay window setpoint high
[30]
Set Relay window hysteresis
[31]
Select Internal temperature sensor
Select CJC connector (Accessory)
[34]
Select Open relay contact at error
Select Close relay contact at error
[37]
Select 0-20 mA outout range
Select 4-20 mA output range
Select 20-0 mA output range
Select 20-4 mA output range
[38]
Select No error action - output undefined at error
Select Downscale at error
Select Namur NE43 downscale at error
Select Namur NE43 upscale at error
[39]
Select Analogue output response time in seconds.
[41]
Set Temperature for analogue output low
[42]
Set Temperature for analogue output high
[43]
Enter SIL setup
Enter Simulation mode
Enter Rail setup
Perform Process Calibration
Enter Language setup
Enter Password setup
Enter Display setup
Perform Memory operations
[44]
Load saved configuration into module
Save configuration in display front
[45]
Adjust LCD contrast
[46]
Adjust LCD backlight
[47]
Write a 5-character channel TAG
[48]
Show Analog output value in display
Show TAG on display
Alternate shown information in display
[49]
Calibrate Input low to process value?
[50]
Calibrate Input high to process value?
[51]
Enable input simulation?
[52]
Set the input simulation value
[53]
Relay simulation - use 1 to toggle relay
[54]
Enable Password protection?
[55]
Set New password
[56]
Enable Fastset functionality?
[57]
Relay setpoint - press 3 to save
safety Manual
21
Publicidad
Capítulos
Tabla de contenido
