User Instructions; General Safety Instructions; Warning - AXXAIR SX122-A Instrucciones Originales

INNOVATIVE ORBITAL SOLUTIONS

User instructions:

General Safety Instructions:

WARNING! In order to reduce all risks of possible body harm when using electric equipment. PLEASE READ THESE
INSTRUCTIONS THOROUGHLY BEFORE USING THE MACHINES. Keep these safety instructions.The machine must only
be used by qualified technicians who have been trained to use the equipment.
This machine should be used only for the job for which it was designed.
Keep your working area tidy. Untidiness increases the risks of accidents.
Consider the work area environment in which you use the equipment. Do not expose the electric tools to the rain. Do not use them
in a humid or wet environment or in the presence of inflammable gases or liquids. Always work in a well-lit place.
Protect yourself against electric shocks. Avoid being in touch with areas related to the ground.
When not in use, tools should be stored in a dry, secure place.
Dress properly with clothes adapted for the job. Do not wear loose clothing or jewellery. They could be caught up in moving parts.
Use the safety glasses provided with the machine. You can also use a face or dust mask if the cutting operation is dusty.
Do not abuse the cable. Never carry the machine by the cable or yank it to disconnect from plug.
Keep the cable away from heat, oil and sharp objects. Inspect cable regularly and if damaged, have it repaired by authorised after-
service facility.
Secure the machine on a workbench or into the ground via the security leg in order to work safety.
Maintain tools with care. Keep the machine clean for a better and safer performance. Follow instructions for lubricating and
changing accessories.
Unplug the machine when not in use, before maintaining, and when changing accessories (e.g. blades).
Avoid unintentional starting. Do not carry plugged-in tool with finger on switch. Be sure the switch is off when plugging in.
Use appropriate extension cords. When using the machine outdoor, use only extension cords intended for outdoor use.
Stay alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired.
Check if your machine is damaged. Before using the machine ALWAYS check that no parts have been damaged in order to be sure
that it can perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting,
and any other conditions that may affect its operation. Damaged parts should be properly repaired or replaced by an authorised
after-service centre. DO NOT USE MACHINE IF DAMAGED.
Use AXXAIR accessories only.
Repairing by experts only. The machine is in accordance with the relevant safety rules.
If you are using an electric motor make sure that the voltage is the appropriate.
If you are using a pneumatic motor, check the pressure of the compressed air (6 bars). Output: see relevant chapter. The use of an
oil filter is MANDATORY; you can obtain it on request.
Always check that the handle and the safety pedal has been provided with the machine.(for a pneumatic machine only).
Use appropriate means for handling the machine.

Warning:

Arc-welding can be dangerous for the operator as well as for all persons in the vicinity. Take all appropriate safety
precautions before using the welding machine. Observe and obey the safety procedures imposed by your employer; these
procedures should be based on the rules and regulations in force as well as on the manufacturer's recommendations.
Electric Shock = Potential loss of life.

Install and earth the welding equipment, following the rules and regulations in force.

Do not touch live parts. Do not touch electrodes with bare hands or wet gloves.

Insulate yourself from the ground and from the workpiece.

Ensure that the work position adopted is safe both for the operator and for persons nearby.
Fumes and gas = Potential health hazard:

Keep your face as far away from welding fumes as possible.

Provide ventilation and evacuation of welding fumes using a suitable device that provides a safe working
environment.
Light rays from the arc = These can damage your eyes and burn your skin.

Protect your eyes and skin. Use a protective visor and wear safety clothing and protective gloves.

Protect nearby persons from injury due to welding by providing protective curtains.
Join experience
0
In the event of a malfunction, contact qualified service personnel only.
SAS au capital de 135 720 € - RCS Romans B414 581 363 – Code APE 2841 Z – Siret 414 581 363 00028 – TVA FR13414 581 363
330B Route de Portes Les Valence - ZI Les Bosses - 26800 Etoile sur Rhône
Tél: +33 475 575 070 - Fax: +33 475 575 080 - commerce@axxair.com - www.axxair.com
- 16 -
English