Technical Specifications - Ribind S1 Manual De Instrucciones

Ocultar thumbs

Contenido

Tabla de contenido

Idiomas disponibles

The photocell input (PHOT - COM) is a NORMALLY CLOSED contact.

In case there are more couple of photocells, the contacts from all the photocell receivers

could be connected in series.

In case the photocells are not installed, this contact must be short circuited with a wire jump

(from PHOT to COM) to permit the gate to operate.

ATTENTION: In case the receiver led remains lit, malfunctioning of the main supply

is suspected.

It is advisable to connect electrically to earth the

columns or the photocells stands to the terminal A -, to

shield the photocells from external noise.

Be careful not to short circuit the system when the

supply phases are inverted!

AUTOMATIC CLOSING after the transit through the photocell (DIP17 ON)

This option could be useful to close automatically the gate when the vehicle left and

disengaged the photocell beam. If the DIP17 is turned ON, this function is activated and the

PHOTO input will have two purposes:

- detect the obstacle and prevent the gate movement in according with the DIP6 position

- close the gate as soon as the vehicle leaves the photocell beam

If DIP17 ON and DIP6 OFF

If the gate is opening and a vehicle crosses the photo beam, the gate will stop. When

the vehicle leaves, the gate will close automatically after 1second pause.

If DIP17 ON and DIP6 ON

If the gate is opening and a vehicle crosses the photo beam, the gate will continue to

open. When the vehicle leaves, the gate will stop and then closes automatically after

1second pause.

If the complete gate open position is reached before the vehicle leaving, the DIP17 will be

ignored and the automatic closing will be managed in according to the DIP3 position.

PAY ATTENTION: it is highly recommended to check photocells operation at least

every 6 months.

SAFETY ENCODER (PLUS operators, only)

The Encoder acts as a safety device both during gate closing and opening by reversing the

motor movement in case of impact detection. Any impact is detected if the motor shaft

turning has been suddenly and unexpected blocked.

If the Encoder is faulty (lack of power, disconnected cables, broken or defective disk), the

gate will not move.

STATE OF ALARM FROM ENCODER impact detection

If the gate is moving and the first encoder impact detection occurs, the gate will reverse in the

opposite direction. If a further encoder impact detection occurs, the gate will reverse again

just for 1second. Then, it will stop and the alarm status will be indicated by the blinking unit

(flashes for 1minute) and by led DL1 (blinks every 2 seconds).

To recover the normal gate operation, it is necessary towait 1 minute or press any control

buttons.

SAFETY STRIP (EDGE - COM)

If it intervenes during opening, it inverts the movement and closes for 2 seconds and then

stops.

If it intervenes during closing, it inverts the movement and opens for 2 seconds and then

stops.

If the safety strip remains engaged (NO contact), no automatic movement is allowed.

In case the safety strip is not installed, this contact must be short circuited with a wire jump

(from EDGE to COM) to permit the gate to operate.

PAY ATTENTION: it is highly recommended to check safety-strips operation at least

every 6 months.

SAFETY STRIP ALARM

After the inversion given by the intervention of the safety edge, the gate stops in alarm mode

and this is signaled by the blinker on for 1 minute.

During or after the minute of alarm, the normal gate operations can be restored by pressing

any push button.

TESTING THE SAFETY STRIP equipment (DIP12 ON)

The DIP12 ON enables the Test of safety strip equipment. The Test is performed every time

the gate completes a full opening. It is suitable only if the safety strip device is equipped with

a dedicated power supply input.

In fact, the safety strip equipment power supply input has to be connected to the A+TEST

and A- outputs (DIP12 ON). Automatically, every time the gate completes a full opening, just

before closing, the control board switches OFF the A+TEST and A- power supply output

for a very short time. While the safety strip power supply is switched OFF, if everything is

working fine the safety strip contact (EDGE - COM) must open. In case the test fails, no other

gate manoeuvre will be allowed and the alarm state will be signalled by the Blinker that will

remain on.

NOT ALL THE SAFETY STRIPS CAN BE TESTED, THUS THE SWITCH DIP12 MUST BE LEFT

OFF.

STOP BUTTON (COM-STOP)

24Vdc

During all the gate movement, the STOP button will stop the motor.

If it is pressed when the gate is still and completely open (or partially open in the pedestrian

Term.

A -

position), automatic closing will be temporarily disabled even if DIP3 is turned ON. Therefore,

a new command will be needed to close the gate.

FUNCTIONING IN DEAD MAN MODE WHEN THE SAFETY DEVICES ARE FAILING

If the safety edge fails or remains engaged for more than 5 seconds, or if photocell fails

or remain engaded for more than 60 seconds, the open, close, k button and pedestrian

commands will work only in dead man mode.

The signal that this mode has been activated is given by the blinking of the programming led.

With the blinking of the programming led, the opening and closing operation are allowed

only with the command button pressed and held. The radio commands and that of automatic

closing, will be excluded, since their use in this mode, is not allowed by the norms.

Once the failing safety device is repaired, in automatic after 1 second, all standard

commands that were selected, such as step by step, automatic mode, radio commands and

automatic closing start functioning again.

Note 1: during this functioning in dead man mode, in case of damage to the safety strips

(or photocells) the photocells (or safety strips) still work by interrupting the operation

in progress.

Note 2: the stop command is not to be considered a safety command that can be bypassed

in this mode. Therefore, when pressed or damaged, it will not allow any movement

of the gate.

The dead-man operation is only an emergency operation which must be activated

for a very short period and with the complete installation at sight so to have a

secure and safe control of the system. As soon as possible however, the failing

safety devices must be repaired and activated.

FLASHING LIGHT

Connect the flashing light to J1 flashing light outputs, use flashing lights ACG7059 and bulbs

of 40W maximum.

NOTE: This electronic K board can only supply power to FLASHING LIGHTS with inbuilt

flashing circuit.

PRE-FLASHING function

The DIP8 in the ON position enables the pre-flashing, the FLASHING LIGHT starts working 3

seconds before every movement of the gate.

The DIP8 in the OFF position disables any pre-flashing, the FLASHING LIGHT and the motor

will star at the same time.

OPEN GATE INDICATOR (SIGNAL-COM)

It indicates the gate status: open, partially open or not completely closed.

It switches off only when the gate is completely closed.

During programming, this indicator is active.

NOTE: if button panels or bulbs are in excess, the electronic board logic will be impaired and

operations might stop.

PROBE

It's a cable ended with a sensor to detect the motor temperature and, if necessary, to active

automatically the motor warming (code ACG4665).